(2)
Access Panel
119B1 Main Equipment Center
B.
Prepare to Remove the Parking Brake Switch
S 492-101
(1) Put the chocks below the wheels.
S 842-004
CAUTION: DO NOT USE THE PARKING BRAKE HANDLE TO RELEASE THE PARKING
_______ BRAKE. IF YOU PUSH OR TWIST THE HANDLE, IT CAN CAUSE DAMAGE TO THE HANDLE LINKAGE.
(2)
Push and release the two brake pedals to release the parking brake.
S 862-006
(3)
Open this circuit breaker on the main power distribution panel, P6, and attach DO-NOT-CLOSE tag:
(a)
6F4, LANDING GEAR PARKING BRAKE VLV
C.
Remove the Parking Brake Switch
S 842-007
(1) Get access to the switch in the forward equipment bay which is below the control cabin.
32-44-08
ALL ú ú 02 Page 201 ú May 28/02
A
757
MAINTENANCE MANUAL
RUDDER
PEDAL ARMS
RIG PIN
R1A
PARKING BRAKE
MECHANISM
SEE A
SEE B
PARKING
BRAKE
CABLE
SUPPORT
STRUCTURE
FOR THE
RUDDER PEDAL
PARKING BRAKE MECHANISM A
PARKING BRAKE RELEASED
CONTROL ARM PARKING BRAKE SWITCH, S459
ATTACH SCREW FOR THE SWITCH (2 LOCATIONS)
PARKING
SWITCH SUPPORT
BRAKE SET
STOP BUMPER
INSTALL A 0.25 INCH THICK SHIM
BETWEEN THE STOP BUMPER AND
THE CONTROL ARM
(SEE THE SWITCH ADJUSTMENT)
B
Parking Brake Switch Installation Figure 201
32-44-08
ALL ú ú 02 Page 202 ú May 28/99
A
757 MAINTENANCE MANUAL
S 032-008
(2)
Disconnect the electrical wires from the switch.
S 032-009
(3)
Remove the two bolts which hold the switch to the structure for the rudder pedal.
S 032-010
(4)
Remove the switch assembly.
TASK 32-44-08-402-023
3. Install the Parking Brake Switch (Fig. 201)
________________________________
A. Access
(1)
Location Zones
119/120 Main Equipment Center
211/212 Control Cabin
(2)
Access Panel
119B1 Main Equipment Center
B.
Install the switch.
S 842-024
(1)
Make sure the parking brake handle is released.
S 432-034
(2)
Install the switch assembly as follows:
(a)
Put the switch assembly at the two attach holes in the support housing for the rudder pedal.
(b)
Loosely install two screws through the switch assembly and the mating holes in the housing for the rudder pedal.
NOTE: The aft attach hole in the switch support fitting has a
____ slot to permit the switch assembly to move down.
(c)
Move the switch assembly down until the attach screw is at the bottom of the slot.
(d)
Do not tighten the screws until the switch adjustment is done.
32-44-08
ALL ú ú 04 Page 203 ú May 28/99
A
757 MAINTENANCE MANUAL
S 822-041
(3) Adjust the parking brake switch (AMM 32-44-00/501).
TASK 32-44-08-022-042
4. Adjust the Parking Brake Switch (Fig. 201)
_______________________________
A. Equipment
(1)
Ohmmeter - Commercially Available
(2)
Rig pin R1A-P/N B20003-26, part of kit
B20003-70 (AMM 20-10-24/201). ú (3) Rig pin R1A-P/N B20003-26, part of kit ú B20003-XX (AMM 20-10-24/201).
B. References
(1)
AMM 32-44-00/501, Parking Brake System
(2)
WDM 32-44-11, Parking Brake System
C.
Access
(1)
Location Zones
119/120 Main Equipment Center
211/212 Control Cabin
(2)
Access Panel
119B1 Main Equipment Center
D.
Procedure
S 822-122
(1) Adjust the switch (AMM 32-44-00/501).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊 起落架 CHAPTER 32 - LANDING GEAR 3(69)
