ANTISKID SHUTTLE VALVE
MODULE COMPONENTS

C

Antiskid Shuttle Valve Module/Component Installation
Figure 401 (Sheet 2)

 32-42-07
 ALL  ú ú 01 Page 403 ú Sep 20/90
 
A

757 MAINTENANCE MANUAL
 S 864-047
 (6)  
Remove the pressure from the right and left hydraulic systems and reservoirs (Ref 29-11-00).

 S 864-048

 (7)  
Push in the brake pedals seven times to release the pressure from the brake accumulator.

 TASK 32-42-07-024-061
 3.  Antiskid Shuttle Valve Module - Removal (Fig. 401)_______________________________________
 A. Procedure
 S 944-001
 (1)  
Do the Prepare for Removal procedure (Ref par. 2).

 S 034-002

 (2)  
Disconnect the hydraulic lines from the module and install caps on the lines.

 S 024-003

 (3)  
Remove the module attach bolts and remove the module.

 S 034-004

 (4)  
Remove the hydraulic fittings (four locations) from the ports for the brake hydraulic lines on the module and discard the O-rings.

 S 034-005

 (5)  
Remove the hydraulic fittings (six locations) from the ports on the module for the hydraulic lines that connect to the normal and alternate antiskid valves.

 TASK 32-42-07-404-006
 4.  Antiskid Shuttle Valve Module - Installation (Fig. 401)____________________________________________
 A. Consumable Materials
 (1)  
D00153 Hydraulic Fluid - BMS 3-11

 B.
References

 (1)
29-11-00/201, Pressurize/Depressurize Main Hydraulic Systems

 C.
Access

 (1)  
Location Zones
 143 Left Main Landing Gear Wheel Well
 144 Right Main Landing Gear Wheel Well

 D.
Procedure

 32-42-07
 ALL  ú ú 01 Page 404 ú May 28/02
 
A
757
MAINTENANCE MANUAL

 S 644-066
 CAUTION:_______ IF YOU INSTALL ANTISKID SHUTTLE VALVE MODULE PART NUMBER
 2-8051-1 OR 2-8051-1MOD AS A SPARE OR TO PREVENT A FLUID
 TRANSFER OCCURANCE, IT IS RECOMMENDED THAT THE VALVE MODULE ON
 THE OPPOSITE WING BE THE SAME PART NUMBER.  THE 2-8051-1 OR
 2-8051-1MOD MODULES ARE DESIGNED TO DECREASE OR PREVENT RIGHT
 TO CENTER SYSTEM HYDRAULIC FLUID TRANSFER.  IF THE 2-8051-1 OR
 2-8051-1MOD VALVE MODULE IS MIXED WITH A 2-7460-3 OR 2-7460-4

 VALVE, FLUID TRANSFER CAN OCCUR.
 (1)  
Lubricate the O-rings and the hydraulic fittings before you install them in the module.

 S 434-008

 (2)  
Install the hydraulic fittings (four locations) to the brake ports on the module with new O-rings.

 S 434-009

 (3)  
Install the hydraulic unions (six locations) in the ports for the hydraulic lines that connect to the antiskid valve with new O-rings.

 S 424-010

 (4)  
Install the module with four bolts, washers and nuts (four locations).

 S 424-063

 (5)  
Connect the hydraulic lines to the module.

 S 864-013

 (6)  
Pressurize the right hydraulic system and reservoir (Ref 29-11-00).

 S 864-014

 (7)  
Push in the brake pedals fully four or more times.

 S 794-015

 (8)  
After five minutes, do a check for leaks at the hydraulic tube connections

 S 714-016

 (9)  
Do a test to make sure that the module operates properly as follows:

 (a)  
Push in and release the brake pedals and look to make sure that the brake wear pins for each of the four brakes extend and retract.

 NOTE: This check is to make sure that brake pressure is
____ applied through the module to operate the brakes on the side of the airplane for the module that you replaced.
 

 32-42-07
 ALL  ú ú 01 Page 405 ú May 28/02
 
A

757 MAINTENANCE MANUAL
 (b)  
Remove the pressure from the right hydraulic system (Ref 29-11-00).

 (c)  
Pressurize the left hydraulic system and reservoir (Ref 29-11-00).

 (d)  
Push in the brake pedals fully again and look at the brakes to make sure that the brake on each of the four wheels operates.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 3(41)