S 864-021
(10)
Remove the pressure from the left hydraulic system (Ref 29-11-00).
S 944-022
(11)
Do the steps in the Return the Airplane to Its Usual Condition if more maintenance is not necessary.
TASK 32-42-07-004-023
5. Antiskid Shuttle Valve - Removal (Fig. 401)
________________________________
A. Procedure
S 944-060
CAUTION: DO NOT LET DIRT OR OTHER CONTAMINATION GET IN THE PORTS
_______ OF THE MODULE. THIS CAN CAUSE A MALFUNCTION OF THE UNIT.
(1)
Do the Prepare for Removal procedure (Ref Par. 2)
S 024-024
(2)
Turn the valve until the threads on the valve do not engage the mating threads in the module and remove the valve.
S 034-025
(3)
Remove the retainers and the O-rings from the valve. Discard the O-rings.
TASK 32-42-07-404-049
6. Antiskid Shuttle Valve - Installation (Fig. 401)
_____________________________________
A. Consumable Materials
(1)
D00153 Hydraulic Fluid - BMS 3-11
B.
References
(1)
29-11-00/201, Pressurize/Depressurize Main Hydraulic Systems
C.
Access
(1)
Location Zones
143 Left Main Landing Gear Wheel Well
144 Right Main Landing Gear Wheel Well
D.
Procedure
32-42-07
ALL ú ú 01 Page 406 ú May 28/02
A
757 MAINTENANCE MANUAL
S 434-028
CAUTION:_______RUBBER AND TEFLON O-RINGS ARE NOT INTERCHANGEABLE. FAILURE TO INSTALL TEFLON O-RINGS CAN CAUSE TRANSFER OF HYDRAULIC FLUID FROM THE NORMAL BRAKE SYSTEM TO THE ALTERNATE BRAKE SYSTEM.
(1)
Lubricate the O-rings (new) and the retainers with hydraulic fluid and install them on the valve.
S 424-050
(2)
Install the valve in the module, tighten to 300 pound-inches and install a lockwire.
S 864-051
(3)
Pressurize the right hydraulic system and reservoir (Ref 29-11-00).
S 794-052
(4)
After five minutes, do a check of the valve installation for leaks.
S 714-053
(5)
Do an operational test of the valve as follows:
(a)
Do the test in Par. 4.D.(9). again but only do a check to make sure that the brake operates that gets pressure through the hydraulic line from the valve that you replaced.
S 944-054
(6) Do the steps in the Return the Airplane to Its Usual Condition procedure if more maintenance is not necessary.
TASK 32-42-07-004-031
7. Antiskid Shuttle Valve Filter - Removal (Fig. 401)_______________________________________
A. Procedure
S 864-062
(1) Do the Prepare for Removal procedure (Ref Par. 2)
S 424-055
CAUTION: DO NOT LET DIRT OR OTHER UNWANTED MATERIAL GET IN
_______ THE PORTS OF THE FILTER. IF THIS HAPPENS, A MALFUNCTION OF THE VALVE CAN OCCUR.
(2)
Turn the filter counterclockwise until you can remove it from the module.
S 434-030
(3)
Remove the retainers and the O-rings from the filter. Discard the O-ring.
32-42-07
ALL ú ú 01 Page 407 ú May 28/02
A
757 MAINTENANCE MANUAL
TASK 32-42-07-404-032
8. Antiskid Shuttle Valve Filter - Installation (Fig. 401)
____________________________________________
A. Consumable Materials
(1)
D00153 Hydraulic Fluid - BMS 3-11
B.
References
(1)
29-11-00/201, Pressurize/Depressurize Main Hydraulic Systems
C.
Access
(1)
Location Zones
143 Left Main Landing Gear Wheel Well
144 Right Main Landing Gear Wheel Well
D.
Procedure
S 644-033
(1)
Lubricate the O-rings (new) and the retainers with hydraulic fluid and install them on the filter.
S 424-034
(2)
Install the filter in the module, tighten to 300 pound-inches and install a lockwire.
S 864-056
(3)
Pressurize the right hydraulic system and reservoir (Ref 29-11-00).
S 794-035
(4)
After five minutes, do a check of the filter installation for leaks.
S 944-057
(5)
Do the steps in the Return the Airplane to Its Usual Condition paragraph if more maintenance is not necessary.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 3(42)
