MECHANISM THAT ADJUSTABLEADJUSTABLE OPERATES THE PUSHRODPUSHROD FORWARD DOOR
A
3. WASHER
2. SCREW SHIMS
4. NUT (REF)
1. NOSE LANDING GEAR WHEEL WELL
DOOR CLOSED SENSOR FORWARD WALL
(S10243, SYSTEM 1)
SENSOR BRACKET
0.16
INCH 0.14
DOOR
OUTER NOSE LANDINGSEAL 5. TARGET SKIN GEAR DOOR
0.12
INCH 0.10
4. NUT
3. WASHER
2. SCREW WHEEL WELL
A-A SHIMS 1. NOSE LANDING GEAR
(REF)FORWARD WALL
DOOR CLOSED SENSOR (S10081, SYSTEM 2)
SENSOR 5. TARGET BRACKET 0.16
INCH 0.14
DOOR OUTER SEAL 0.12
INCHSKIN
0.10 NOSE LANDING GEAR DOOR
B-B
Nose Landing Gear Door Closed Sensors Figure 202
32-61-03
ALL ú ú 01 Page 205 ú Sep 20/95
A
757
MAINTENANCE MANUAL
RETRACT
ACTUATOR
1. CONDUIT CONNECT PANEL
SEE A
WHEEL WELL AFT WALL (REF)
TOP DRAG STRUT
SEE B
SEE C
TOP OF THE WHEEL WELL (REF)
FWD
1. CONDUIT CONNECT PANEL
3. WIRE BUNDLE
WHEEL WELL AFT WALL (REF)
2. FLEXIBLE CONDUIT A
Nose Landing Gear Locked Sensors
Figure 203 (Sheet 1)
32-61-03
ALL ú ú 01 Page 206 ú Sep 20/95
A
757 MAINTENANCE MANUAL
2. FLEXIBLE CONDUIT
6.0 INCHES
(152.4 mm) BETWEEN CLAMPS
WHEEL WELL
RETRACT AFT WALL
ACTUATOR
4. AFT LOCK LINK
TOP DRAG STRUT
5. FORWARD LOCK LINKFWD
B
4. AFT LOCK LINK
0.04-0.05 INCH SPRING
(1.02-1.27 mm) 7. NUT
6. NUT 8. WASHER
FORWARD LOCK LINK
12. SPACER WASHER 2. FLEXIBLE 11. LAMINATED SHIMS CONDUIT
9.
NOSE LANDING GEAR
10.
SENSOR TARGET FWD
10.0 INCHES(UP/DOWN) LOCKED (254 mm)SENSOR BETWEEN CLAMPS
1
1
S10065, SYSTEM 1, RIGHT
C
S10078, SYSTEM 2, LEFT
Nose Landing Gear Locked Sensors
Figure 203 (Sheet 2)
32-61-03
ALL ú ú 01 Page 207 ú Sep 28/01
A
757 MAINTENANCE MANUAL
(5) S 032-015Remove the conduit (2) from the sensor (8) and use the line to pull the sensor wires through the conduit (2).
(6) S 092-016Remove the line from the sensor wires. Keep the line in the conduit to help when you install the replacement sensor wire through the conduit.
(7) S 032-017Remove the nut (7) and washer (8) from the sensor (9) on the target side of the sensor.
(8) S 022-018Remove the sensor (9) from the aft lock link (4).
NOTE:____ Keep the nuts and washers and write down the location of the washer for the installation of the sensor.
(9) S 022-094If required, use the following steps to remove the conduit. (a) Disconnect conduit from bracket on aft wheelwell bulkhead. (b) Remove all clamps from conduit.
32-61-03
ALL ú ú 01 Page 208 ú Sep 28/01
A
757 MAINTENANCE MANUAL
TASK 32-61-03-402-019
3. Install the Proximity Sensor for the Nose Landing Gear
______________________________________________________
A. Parts
~.............................................................................. | AMM | | AIPC | .................. ........................... | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 201 | 1 | Sensor | 32-61-03 | 03 | 35 | | | 2 | Screws | 32-61-03 | 03 | 30 | | | 3 | Shims | 32-61-03 | 03 | 40 | | | | | | | 42 | | | | | | | 43 | | | | | | | 44 | | 202 | 1 | Sensor | 32-61-03 | 02 | 45 | | | 2 | Screw | 32-61-03 | 02 | 25 | | | 3 | Washer | 32-61-03 | 02 | 30 | | | 4 | Nut | 32-61-03 | 02 | 37 | | 203 | 6 | Nut | 32-61-03 | 04 | 5 | | | 7 | Nut | 32-61-03 | 04 | 18 | | | 8 | Washer | 32-61-03 | 04 | 17 | | | 9 | Sensor | 32-61-03 | 04 | 20 | | | 10 | Sensor Target | 32-61-03 | 04 | 15 | | | 12 | Washer | 32-61-03 | 04 | 10 | 2.......…........…...................................…..........…......….......1
B. References
(1)
AMM 32-00-15/201, Landing Gear Door Locks
C.
Install the Up, Down, and Door Closed Sensor for the Nose Landing Gear (Fig. 201 and 202)
(1)
Install the sensor wire in the wire bundle.
(2)
Loosely install the clamps that hold the wire bundles.
S 422-022 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 3(166)
