国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽

  • 熱門標簽

當前位置: 主頁 > 航空資料 > 國外資料 >

時間:2010-05-28 01:11來源:藍天飛行翻譯 作者:admin
曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

been received, the pilot is expected to start a speed
reduction so that the aircraft will cross the fix,
initially, at or below the maximum holding airspeed.
e. When no delay is expected, the controller
should issue a clearance beyond the fix as soon as
possible and, whenever possible, at least 5 minutes
before the aircraft reaches the clearance limit.
f. Pilots should report to ATC the time and
altitude/flight level at which the aircraft reaches the
clearance limit and report leaving the clearance limit.
NOTEIn
the event of two‐way communications failure, pilots are
required to comply with 14 CFR Section 91.185.
g. When holding at a VOR station, pilots should
begin the turn to the outbound leg at the time of the
first complete reversal of the to/from indicator.
h. Patterns at the most generally used holding
fixes are depicted (charted) on U.S. Government or
commercially produced (meeting FAA requirements)
Low or High Altitude Enroute, Area and STAR
Charts. Pilots are expected to hold in the pattern
depicted unless specifically advised otherwise by
ATC.
NOTEHolding
patterns that protect for a maximum holding
airspeed other than the standard may be depicted by an
icon, unless otherwise depicted. The icon is a standard
holding pattern symbol (racetrack) with the airspeed
restriction shown in the center. In other cases, the airspeed
restriction will be depicted next to the standard holding
pattern symbol.
REFERENCEAIM,
Holding, Paragraph 5-3-7j2.
i. An ATC clearance requiring an aircraft to hold
at a fix where the pattern is not charted will include
the following information: (See FIG 5-3-2.)
1. Direction of holding from the fix in terms of
the eight cardinal compass points (i.e., N, NE, E, SE,
etc.).
2. Holding fix (the fix may be omitted if
included at the beginning of the transmission as the
clearance limit).
3. Radial, course, bearing, airway or route on
which the aircraft is to hold.
4. Leg length in miles if DME or RNAV is to be
used (leg length will be specified in minutes on pilot
request or if the controller considers it necessary).
5. Direction of turn if left turns are to be made,
the pilot requests, or the controller considers it
necessary.
6. Time to expect further clearance and any
pertinent additional delay information.
AIM 2/14/08
5-3-10 En Route Procedures
FIG 5-3-2
Holding Patterns
TYPICAL PROCEDURE ON AN ILS OUTER MARKER
EXAMPLES OF HOLDING
L OM M M
RUNWAY
VOR
VOR
TYPICAL PROCEDURE AT INTERSECTION
OF VOR RADIALS
HOLDING COURSE
AWAY FROM NAVAID
HOLDING COURSE
TOWARD NAVAID
VORTAC
15 NM DME FIX 10 NM DME FIX
TYPICAL PROCEDURE AT DME FIX
2/14/En Route Procedures 5−3−11
FIG 5−3−3
Holding Pattern Descriptive Terms
ABEAM
HOLDING SIDE
OUTBOUND
END
HOLDING
COURSE
OUTBOUND
INBOUND
NONHOLDING SIDE
FIX END
RECIPROCAL
FIX
j. Holding pattern airspace protection is based on
the following procedures.
1. Descriptive Terms.
(a) Standard Pattern. Right turns
(See FIG 5−3−3.)
(b) Nonstandard Pattern. Left turns
2. Airspeeds.
(a) All aircraft may hold at the following
altitudes and maximum holding airspeeds:
TBL 5−3−1
Altitude (MSL) Airspeed (KIAS)
MHA − 6,000’ 200
6,001’ − 14,000’ 230
14,001’ and above 265
(b) The following are exceptions to the
maximum holding airspeeds:
(1) Holding patterns from 6,001’ to
14,000’ may be restricted to a maximum airspeed of
210 KIAS. This nonstandard pattern will be depicted
by an icon.
(2) Holding patterns may be restricted to a
maximum speed. The speed restriction is depicted in
parenthesis inside the holding pattern on the chart:
e.g., (175). The aircraft should be at or below the
maximum speed prior to initially crossing the holding
fix to avoid exiting the protected airspace. Pilots
unable to comply with the maximum airspeed
restriction should notify ATC.
(3) Holding patterns at USAF airfields
only − 310 KIAS maximum, unless otherwise
depicted.
(4) Holding patterns at Navy fields only −
230 KIAS maximum, unless otherwise depicted.
(5) When a climb−in hold is specified by a
published procedure (e.g., “Climb−in holding
pattern to depart XYZ VORTAC at or above 10,000.”
or “All aircraft climb−in TRUCK holding pattern to
 
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址:航空信息手冊2008上(191)
国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽
91高清免费视频| 久久久久久久香蕉网| 国产传媒一区| 亚洲免费在线精品一区| 国产在线青青草| 久久九九精品99国产精品| 日本中文字幕久久看| dy888夜精品国产专区| 国产精品国模在线| 免费在线精品视频| 久久精品91久久香蕉加勒比 | 欧美在线观看网址综合| 久久福利一区二区| 日韩视频在线视频| 久久精品magnetxturnbtih| 日本午夜激情视频| 久久99精品久久久水蜜桃| 日韩亚洲一区在线播放| 久草精品在线播放| 青草青草久热精品视频在线观看| 久久久久免费视频| 欧美日韩dvd| 久久精品中文字幕| 国产一区视频在线播放| 欧美成在线观看| 国产免费观看久久黄| 欧美激情网友自拍| 99精品国产高清一区二区| 亚洲啊啊啊啊啊| 国产ts一区二区| 欧洲黄色一级视频| 国产精品欧美日韩一区二区| 国产中文欧美精品| 一本一生久久a久久精品综合蜜| 成人精品水蜜桃| 天天综合狠狠精品| 久久久久久久久综合| 日韩免费一级视频| 国产精品视频精品视频| 国产欧美日韩一区二区三区| 亚洲最大激情中文字幕| 国产精品6699| 欧美日韩国产不卡在线看| 麻豆成人在线看| 91免费视频网站在线观看| 欧美一区二区三区综合| 久久久久久这里只有精品| 蜜桃麻豆91| 亚洲一区亚洲二区| 久久草.com| 国产日韩欧美中文| 欧美一区二区三区综合| 久久久久久久有限公司| 国产自偷自偷免费一区| 亚洲精品中文字幕乱码三区不卡 | 国产精品欧美激情在线观看| 国产在线视频一区| 亚洲综合中文字幕在线| 久久久久久人妻一区二区三区| 国产中文欧美精品| 色婷婷精品国产一区二区三区| 国产精品无码一区二区在线| 国产女人18毛片| 日韩中文不卡| 精品乱色一区二区中文字幕| 国产成人一区二区| 国内精品**久久毛片app| 亚洲精品乱码视频| 国产精品极品在线| 国产suv精品一区二区| 国产奶头好大揉着好爽视频| 日本乱人伦a精品| 欧美精品999| 久久深夜福利免费观看| 777午夜精品福利在线观看| 免费久久久一本精品久久区| 水蜜桃亚洲精品| 欧美日本高清一区| 久久久久无码国产精品一区| 白白操在线视频| 美日韩精品免费| 热久久免费国产视频| 精品国产成人av在线免| 国产成人无码av在线播放dvd | www.亚洲免费视频| 国产精品333| 国产精品稀缺呦系列在线| 欧美一级成年大片在线观看| 亚洲国产一区二区精品视频| 美女黄色丝袜一区| 国产成人免费91av在线| 久久人91精品久久久久久不卡| 国产伦精品一区| 精品一区二区三区无码视频| 奇米888一区二区三区| 亚洲免费视频一区| 中国人体摄影一区二区三区| 国产精品日韩欧美一区二区三区| 国产成人永久免费视频| 91精品国产沙发| 成年人网站国产| 国产免费黄视频| 国产熟人av一二三区| 好吊色欧美一区二区三区| 人人干视频在线| 午夜精品久久久久久久久久久久久| 精品国产综合| 久久夜色精品国产| 久久成年人视频| 国产精品高潮呻吟视频| 国产精品日韩av| 久久久精品国产亚洲| 久久久久久国产免费| 国产成人亚洲综合无码| 国产成人精品电影| 九色综合婷婷综合| 日韩在线观看你懂的| 九九九九免费视频| 九九九久久久| 久久精品国产亚洲精品2020| 久久精品国产精品国产精品污| 国产精品99免视看9| 91精品在线看| 久热免费在线观看| 91精品黄色| 久久久久久a亚洲欧洲aⅴ| 国产成人av影视| 日韩专区在线播放| 国产精品网站免费| 精品国产一区二区三区在线| 中文字幕综合在线观看| 亚洲综合激情五月| 天堂资源在线亚洲资源| 日韩欧美精品一区二区| 欧美资源一区| 欧美精品欧美精品| 国产在线视频不卡| 成人精品在线观看| 国产成人精品免费久久久久| 精品国产拍在线观看| 国产精品美女久久久久久免费| 不卡伊人av在线播放| 一区二区精品免费视频| 欧美一区二区三区四区在线 | 色综合666| 欧美亚洲成人网| 免费国产在线精品一区二区三区| 国产一区免费在线观看| 高清欧美性猛交xxxx| 国产富婆一区二区三区| 久久精品成人动漫| 精品国产乱码久久久久久久软件| 亚洲最大福利网| 日韩电影天堂视频一区二区| 欧美第一黄网| 国产精品夜色7777狼人| 久久亚洲综合网| 国产精品偷伦一区二区| 久久99热精品这里久久精品| 亚洲综合日韩在线| 欧美在线一二三区| 国产精品一区二区久久精品| 777精品视频| 国产精品免费福利| 亚洲永久一区二区三区在线| 人人做人人澡人人爽欧美| 国产又粗又长又爽视频| 91国产在线免费观看| 国产成人精品在线观看| 欧美激情中文网| 欧美牲交a欧美牲交aⅴ免费下载| 国产男人精品视频| 色噜噜狠狠狠综合曰曰曰88av| 精品中文字幕乱| 日本精品免费在线观看| 国产欧美精品va在线观看| 久久国产亚洲精品无码| 国产精品久久久久久久9999| 午夜精品久久久久久久99黑人 | 国产精品视频中文字幕91| 中文一区一区三区免费| 欧美日韩精品久久| 97人人模人人爽人人喊38tv| 国产精品手机在线| 日日噜噜噜噜夜夜爽亚洲精品| 国产午夜大地久久| 色偷偷偷亚洲综合网另类| 亚洲欧洲一区二区在线观看| 免费在线精品视频| 久久久久久a亚洲欧洲aⅴ| 精品不卡在线| 欧美精品欧美精品系列c| 国产精品99蜜臀久久不卡二区| 欧美成人在线网站| 欧美中文字幕在线| 久久免费国产视频| 亚洲激情一区二区三区| 国产亚洲天堂网| 俺去亚洲欧洲欧美日韩| 亚州av一区二区|