曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Components shall have been tested to the requirements listed in the above table within 18 months of the date Honeywell
receives the components. The soldering test date (month and year) shall be noted on the Certificate of Conformance supplied
with each shipment.
Revisions: First paragraph added to clarify soldering requirements. Note regarding soldering shelf life removed from this
SPOC. Glendale Orders Only requirements deleted. Rigid PWB paragraph number corrected.
SPOC 326 – Electronics Marking Requirements
If marking permanency is required per the drawing/specification then the parts must meet the applicable marking permanency
(resistance to solvents) requirements of the respective specifications:
PRODUCT TYPE SPECIFICATION METHOD
Semi-Conductors MIL-STD-750 1022
Micro-Electronics MIL-STD-883 2015
Rigid Printed Wiring Boards MIL-P-55110 PARA 3.5.4
Rigid Flex Printed Wiring Boards MIL-P-50884 PARA 3.4.4
Flexible Printed MIL-P-50884 PARA 3.4.4
All Other Parts MIL-STD-202 215
Revisions: No changes.
SPOC 328 – Critical Items – CANCELLED
Revisions: SPOC cancelled.
SPOC 329 – Hardness Critical Item
The parts contain Critical Characteristics shown as Hardness Critical Item / Hardness Critical Process (HCI/HCP). No
substitutions or deviations are permitted.
Revisions: No changes.
SPOC 330 – Soldering Requirements – Class 2 – CANCELLED
Revisions: SPOC cancelled.
Aerospace
Supplemental Purchase Order Conditions (SPOC) Manual
UNCONTROLLED IN HARDCOPY
Revision H Effective Date: 15 January 2009 72
SPOC 331 – Soldering Requirements – Class 3 – CANCELLED
Revisions: SPOC cancelled.
*Revised / **Added
SPOC 335 – Tape and Reeled Components *
Surface mount or axial lead components shall be tape and reeled in accordance to the American National Standard EIA - 481.
For order quantities less than 1000; bulk, ammo or rail packaging is acceptable.
Revisions: Olathe Orders Only requirements removed. Statement regarding 1,000 pieces or less orders added.
SPOC 336 – Surface Mount Components – CANCELLED
Revisions: SPOC cancelled.
SPOC 337 – Clean Room Received – CANCELLED
Revisions: SPOC cancelled.
SPOC 338 – Manufacturing Date Less than Two Years – CANCELLED
Revisions: SPOC cancelled.
SPOC 339 – Electronics Axial Lead Components Requirements – CANCELLED
Revisions: SPOC cancelled. Covered by SPOC 335.
Aerospace
Supplemental Purchase Order Conditions (SPOC) Manual
UNCONTROLLED IN HARDCOPY
Revision H Effective Date: 15 January 2009 73
SPOC 340 – Solder Mask Requirement – CANCELLED
Revisions: SPOC cancelled.
SPOC 341 – Micro-Section Inspection Report – CANCELLED
Revisions: SPOC cancelled.
SPOC 349 – Material Samples Required
349.1 Sample Requirements
The Supplier shall supply material samples for the items listed on this Purchase Order. The samples must be:
• Two (2) fully processed test bars and
• One (1) chemistry tab.
349.2 Glendale Orders Only
Process coupons of the material used for fabrication, which have accompanied the components through the processes, shall be
delivered with the finished components. Coupons shall be large enough for analysis and shall be identified (preferably stamped)
with the finished component part number, serial number (as applicable) and related process. A coupon shall be supplied for
each batch of parts going through the process being performed, unless limited by the purchase order.
For Bar/Round Stock, the minimum coupon size shall be d x 6.0”(l), where d = the actual stock diameter for material < 0.5” in
diameter, or where d = 0.5” for stock diameters > 0.5”.
For Plate/Sheet/Forging, the minimum coupon size shall be t x 1.0”(w) x 6.0”(l), where t = the actual thickness for material <
0.5” thick, or where t = 0.5” for stock thickness > 0.5”.
For Heat Treating, the minimum coupon size shall be t x 1.0”(w) x 6.0”(l), where t = the thickness to be within .5” of the thickest
section of the parts being processed.
For Painting and Chemical Conversion Coating, coupons may be sheet material of similar alloy as the parts being processed
with minimum size of 3” x 5” x .025”
The seller shall supply a minimum of two test coupons, 1" X 1" X 9" or 1" diameter X 9", for each heat number shipped. The
minimum size of the test coupons can be 5/8" X 5/8" X 3 1/4" or 5/8" diameter X 3 1/4". The coupons shall have the same
processing histories as the end product. For forged or ring rolling products, a prolongation with sufficient size for making those
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料16(149)