曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Aerowave® 2001
Page 2 of 4 (Code 20-24)
AkzoNobel Aerospace Coatings
1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Fax (847) 625 3200
Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905, Fax (31) 71 308 2056
Internet: www.akzonobel.com/aerospace
AkzoNobel
Aerospace Coatings
Induction Time Not applicable. The product can be used directly after mixing.
Initial Spraying
Viscosity
(21ºC/70ºF)
35 – 65 seconds ISO-Cup 4.
17 – 30 seconds Gardner Signature Zahn-Cup #2
Note: Stir or shake the mixed components thoroughly shortly before measuring the
viscosity.
Note Viscosity measurements are provided as guidelines only and are not to be
used as quality control parameters. Certified information is provided by
certification documentation available on request.
Pot Life
21oC / 70oF – 6 hours
30oC / 86oF – 4 hours
Dry Film
Thickness
(DFT)
15 – 25 μm
0.6 – 1.0 mil
Note The end of Pot Life is not visible by means of viscosity increase. Respect
described Pot Life. Pot Life relates to temperature.
Application
Recommendations
Conditions Temperature:
Relative Humidity:
15 – 35ºC
59 – 95ºF
25 – 80%
Note Aerowave® 2001 may be applied in conditions outside of the the limits shown
above. Care must be excercised to ensure a satisfactory result. Please
contact your local AkzoNobel Aerospace Coatings representative to
determine the proper application techniques when environmental conditions
fall outside of the recommended range.
Equipment Air
HVLP
Air Electrostatic*
Airless/Air Assist
1.2 – 1.6 mm nozzle orifice
1.2 – 1.6 mm nozzle orifice
1.2 – 1.5 mm nozzle orifice
.009 - .013 inch, angle 40o – 60o
Note *) Use Electrostatic spray equipment designed for application of water based
products.
To avoid contamination of water based – solvent based coating products it is
advised to use dedicated water- / solvent-based spray equipment. For
application of water based products use non corrosive spray equipment (e.g.
stainless steel).
Aerowave® 2001
Page 3 of 4 (Code 20-24)
AkzoNobel Aerospace Coatings
1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Fax (847) 625 3200
Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905, Fax (31) 71 308 2056
Internet: www.akzonobel.com/aerospace
AkzoNobel
Aerospace Coatings
Number of
Coats
Spray-apply a homogeneous, wet and closed coat.
Cleaning of
Equipment
Clean the equipment with water directly after use. If necessary, semi-cured
material remaining on the equipment can be cleaned with Solvent Cleaning
C28/15 or Solvent Cleaning 98068.
Note The quality of the application of all coatings will be influenced by the spray
equipment chosen and the temperature, humidity, and air flow of the paint
application area. When applying the product for the first time, it is
recommended that test panels be prepared in order to identify the best
equipment settings to be used in optimizing the performance and appearance
of the coating.
Physical Properties
21ºC/70ºF -
55%
60ºC/140ºF* 80ºC/176ºF*
Surface dry
Dry to handle
Chemical resistant
30 min.
2 hrs
48 hrs
15 min
n.a.
45 min
10 min
n.a.
30 min
*) Substrate surface temperature
When forced cured; allow the paint a 5 minutes ambient flash-off time with
sufficient air movement before entering the oven in order to obtain the best
results.
Recoat minimum*
Recoat maximum*
When surface dry
168 hours. If a drying time of 168 is exceeded
recondition the surface with e.g. Scotch-Brite® type
A very fine
Drying Times
*) In combination with Aerowave Series products. In combination with solvent
based products the minimum recoat time is 8 hrs and the maximal recoat
time is 48 hrs without reconditioning.
Note Curing of waterborne products depends on temperature, relative humidity
and air flow. Increased temperatures, low RH and efficient airflow can
decrease the drying times significantly.
Theoretical
Coverage
29 m2 per liter base material at 15 μm dry film thickness
1163 ft2 per US gallon base material at 0.60 mil dry film thickness
Dry Film
Weight
1.6 g/m2/μm
0.0083 lbs/ft2/mil
Volatile Organic
Compounds
< 120 g/L (1.0 lb/gal) product ready to apply
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料20(73)