Subtask 31-36-34-020-050
B. Removal of the Data Management Unit (DMU)
(1)
Loosen the nuts (4) on the front of the rack (3).
(2)
Lower the nuts (4).
(3)
Pull the DMU (1) on its rack (3) to disconnect the electrical connectors (2).
(4)
Remove the DMU (1) from its rack (3).
(5)
Put blanking caps on the disconnected electrical connectors (2).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-36-34Page 404 1201-210, 1Config-1 Aug 01/05 1 1 1CES 1R **ON A/C 106-149, 159-199, 210-299, 301-399, 401-499,
TASK 31-36-34-000-002
Removal of the FDIU/DMU (FDIMU) (10TV)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
31-36-00-740-015 Printout of the Engine / APU Hours and Cycles Stored in the FDIMU (10TV)
R **ON A/C 106-149, 211-299, 301-399, 401-499,
31-36-34-991-005 Fig. 402
R 1EFF : 106-149, 159-199, 210-299, 301-399, 1 31-36-34Page 405 1401-499, 1Config-1 Aug 01/05 1 1 1CES 1R **ON A/C 106-149, 159-199, 210-299, 301-399, 401-499,
3. Job Set-up
__________ R **ON A/C 106-149, 211-299, 301-399, 401-499,
Subtask 31-36-34-740-060
A. Print out the APU hours and cycles (Ref. TASK 31-36-00-740-015) stored in the FDIMU
Subtask 31-36-34-865-058
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
121VU AIDS & RCDR/FDIMU 5TV K15
Subtask 31-36-34-010-052
C. Get Access
(1) Put the access platform in position in zone 128, at the access door
824.
(2) Open the access door 824.
**ON A/C 159-199, 210-210,
Subtask 31-36-34-550-057
D. On the FDIMU front face, set the ON/OFF switch to OFF.
(1)
To do so open the door, the one bearing the caution: "BEFORE INSTALLING SET INSIDE SWITCH TO ON". Push down the small handle and the door swivels open to show a hole in the upper part with a switch. Use one finger to set the switch to OFF.
(2)
Swivel back the door to its closed position.
R 1EFF : 106-149, 159-199, 210-299, 301-399, 1 31-36-34Page 406 1401-499, 1Config-1 Aug 01/05 1 1 1CES 1R **ON A/C 106-149, 159-199, 210-299, 301-399, 401-499,
4. Procedure
_________ R **ON A/C 106-149, 211-299, 301-399, 401-499,
(Ref. Fig. 402/TASK 31-36-34-991-005)
Subtask 31-36-34-020-053
A. Removal of the FDIMU
(1)
Loosen the nuts (4) on the front of the rack (3).
(2)
Lower the nuts (4).
(3)
Pull the FDIMU (1) on its rack (3) to disconnect the electrical connectors (2).
(4)
Remove the FDIMU (1) from its rack (3).
(5)
Put blanking caps on the disconnected electrical connectors (2).
R 1EFF : 106-149, 159-199, 210-299, 301-399, 1 31-36-34Page 407 1401-499, 1Config-1 Aug 01/05 1 1 1CES 1
Flight Data Interface Management Unit (FDIMU)
Figure 402/TASK 31-36-34-991-005
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-34Page 408 1 1 Config-1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
TASK 31-36-34-400-001
Installation of the Data Management Unit (DMU) (1TV)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM 指示/記錄系統(tǒng) 4(31)
