(5)
Install the DMU (1) on its rack (3).
(6)
Push the DMU (1) on its rack (3) to connect the electrical connectors (2).
(7) Engage the nuts (4) on the lugs (5) and tighten.
**ON A/C 001-049, 051-099, 101-102, 151-199, 201-210,
Subtask 31-36-34-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 4TV
R 1EFF : 001-049, 051-099, 101-102, 151-199, 1 31-36-34Page 412 1201-210, 1Config-1 Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-102, 106-149, 201-202, 211-299, 301-399, R 401-499,
Subtask 31-36-34-554-050
C. Do the AIDS Software Load Procedure (Ref. TASK 31-36-00-710-004) (Ref. TASK 31-36-00-710-008)
**ON A/C 001-049, 051-099, 101-105, 151-158, 201-209,
Subtask 31-36-34-554-052
D. Do the updating of APU hours and cycles data (Ref. TASK 31-36-00-740-004) and of Engine hours and cycles data (Ref. TASK 31-36-00-740-005).
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
Subtask 31-36-34-710-051
E. Do the operational test of the DMU (Ref. TASK 31-36-00-710-001)
**ON A/C ALL
5. Close-up
________
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
Subtask 31-36-34-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the access door 824. (Ref. TASK 52-41-00-410-002)
(3)
Remove the access platform(s).
1EFF : ALL 1 31-36-34Page 413 1 1 Config-1 Aug 01/05 1 1 1CES 1R **ON A/C 106-149, 211-299, 301-399, 401-499,
TASK 31-36-34-400-002
Installation of the FDIU/DMU (FDIMU) (10TV)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
31-33-00-710-013 FDIMU (10TV) DFDRS Software Load Procedure
31-36-00-710-013 FDIMU (10TV) AIDS Software Load Procedure
31-36-00-740-012 Test of the FDIMU (10TV)
31-36-00-740-013 Update of the APU Hours and Cycles in the FDIMU
(10TV) 31-36-00-740-014 Update of the Engine Hours and Cycles in the FDIMU (10TV) 31-36-00-740-015 Printout of the Engine / APU Hours and Cycles Stored
in the FDIMU (10TV) 52-41-00-410-002 Close the Avionics Compartment Doors after Access 31-36-34-991-005 Fig. 402
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 31-36-34Page 414 1 1 Config-1 Aug 01/05 1 1 1CES 1
3. Job Set-up
__________ Subtask 31-36-34-860-058
A. Aircraft Maintenance Configuration
(1)
Print out the engine/apu hours and cycles stored in the FDIMU (Ref. TASK 31-36-00-740-015)
(2)
Make sure that the access platform is in position at the access door 824 in zone 128.
(3)
Make sure that the access door 824 is open. Subtask 31-36-34-865-059
B.
Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU AIDS & RCDR/FDIMU 5TV K15
4. Procedure
_________
(Ref. Fig. 402/TASK 31-36-34-991-005) Subtask 31-36-34-420-053-A
A. Installation of the FDIMU.
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Remove the blanking caps from the electrical connectors (2).
(4)
Make sure that the electrical connectors (2) are clean and in the correct condition.
(5)
Install the FDIMU (1) on its rack (3).
(6)
Push the FDIMU (1) on its rack (3) to connect the electrical connectors (2).
(7)
Engage the nuts (4) on the lugs (5) and tighten.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統(tǒng) 4(33)
