曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (2) Move the moist wad (or pad) ligthly across the surface of the screen (one time only).
 (3) If you find again marks or dust on the screen, do steps (1) and (2) again with a new piece of moist wad (or pad). Do these steps again until the screen is fully clean. 
R R  NOTE : Use a new pad (or wad) each time to prevent scratches that can____ be caused by a dusty pad. 
R R R  (4) Dry the screen with a clean wad (or pad). To do this, move the clean wad (or pad) lightly across the surface of the screen (one time only). 
R R  NOTE : We recommend to frequently clean the screen to remove finger____ marks or dust.
 4. Close-up________
 Subtask 31-63-22-860-051
 A. Make sure that the work area is clean and clear of tool(s) and other items.

 

___________________________________________________________________________
 TASK 31-63-34-000-001
 Removal of the DMC (1WT1,1WT2,1WT3)
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific blanking caps
 No specific circuit breaker(s) safety clip(s)
 No specific access platform 1.6 m (5 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
R  52-41-00-010-002 Open the Avionics Compartment Doors for Access 31-63-34-991-001 Fig. 401
 1EFF : ALL 1 31-63-34Page 401 1 1 Feb 01/03 1 1 1CES 1

 3. Job Set-up
__________
 Subtask 31-63-34-865-050

 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 1WT1
 49VU EIS/DMC1/SPLY 10WT1 E11
 49VU EIS/DMC1/SWTG 21WT1 E09
 FOR 1WT2 121VU EIS/DMC2/SPLY 10WT2 Q08 121VU EIS/DMC2/SWTG 21WT2 R08
 FOR 1WT3 49VU EIS/DMC3/SWTG 21WT3 E07 121VU EIS/DMC3/SPLY 10WT3 Q09
 Subtask 31-63-34-010-050
 B. Get Access
 (1) Put the access platform in position at the access door 824 in zone
 128. R (2) Open the access door 824 (Ref. TASK 52-41-00-010-002).
 4. Procedure
_________ R (Ref. Fig. 401/TASK 31-63-34-991-001) Subtask 31-63-34-020-050
 A. Removal of the DMC
 (1)
 Loosen the nuts (3) on the front of the rack (2).

 (2)
 Lower the nuts (3).

 (3)
 Pull the DMC (5) on its rack (2) to disconnect the electrical connectors (1).

 (4)
 Remove the DMC (5) from its rack (2).

 (5)
 Put blanking caps on the electrical connectors (1).

 1EFF : ALL 1 31-63-34Page 402 1 1 Feb 01/03 1 1 1CES 1

 DMC
 Figure 401/TASK 31-63-34-991-001
 1EFF :  ALL  1  31-63-34 Page 403 
1  1  Feb 01/98
 1  1
 1CES  1

 

 TASK 31-63-34-400-001
 Installation of the DMC (1WT1,1WT2,1WT3)
 1. Reason for the Job__________________
 Self Explanatory
 2. Job Set-up Information______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  access platform 1.6 m (5 ft. 3 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R R  31-32-00-860-008 31-60-00-610-003 31-60-00-610-004 31-60-00-610-005 31-60-00-710-001 52-41-00-410-002 31-63-34-991-001  Procedure to Get Access to the SYSTEM REPORT/TEST/INST Page X LOADING Procedure of the DMC1 X LOADING Procedure of the DMC2 X LOADING Procedure of the DMC3Operational Test of the EISClose the Avionics Compartment Doors after AccessFig. 401
 3. Job Set-up__________
 Subtask 31-63-34-860-050
 A. Aircraft Maintenance Configuration
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 8(7)