曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 C. N1 lIMIT The N1 limit displayed value is the N1 limit value delivered by ECU of the engine for which the N1THR is the greatest or the N1 LIM of ECU linked to the fastest engine if N1.1 - N1.2 > 0,2% or the N1 LIM of ECU remaining valid after one ECU has failed or the N1 LIM of ECU belonging to the engine which is still running after an engine failure. On the ground when both engines are stopped, the displayed N1 limit value is that one delivered by the ECU of the engine the throttle control lever of which is in the most advanced position.
 D. N1 LIM MODE The N1 LIM MODE is the mode in which the above N1 LIMIT value is computed. Obviously , the displayed N1 limit mode is that one delivered by the ECU which is selected to display the N1 limit value . There are 5 possible modes:
 -take-off displayed TO

 -go around displayed GA

 -flexible take off displayed FLX

 -maximum continuous displayed MCT

 -climb displayed CL.
 These modes are selected according to the throttle control lever position
 (the position which is the most advanced is taken into account).
 Detents (mechanical notches) are associated to the mode selection.
 In flexible take off mode, the value of the flexible TAT take off
 temperature, which is entered by the crew through the MCDUs, is displayed
 in cyan color next to the N1 LIM value.
 The indication shows for instance:
 FLX 84.6 % 35 deg.C.

 1EFF : ALL 1 31-66-00Page 8 1 1 Feb 01/05 1 1 1CES 1R **ON A/C 106-149, 303-399, 401-499,

 

 (Ref. Fig. 006)
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
 (Ref. Fig. 007)
 **ON A/C ALL
 E. N1 MAX The N1 MAX value is displayed in analog form by means of a thick amber mark across the N1 scale. N1 MAX is the N1 LIMIT value corresponding to the full forward position of the throttle control lever.
 F. N1 REFERENCE (N1 throttle) The N1 reference symbol (small white circle) represents the N1 predictive value for each engine, in manual mode (the N1 value that would be reached or will be reached in manual control after stabilization, depending on the throttle control lever position).
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
 G. N1 COMMAND The N1 CMD is displayed in analog form by means of a cyan arc of a circle joining the N1 actual needle to the N1 CMD value. Therefore, when the N1 speed is stabilized, this symbol is reduced to a mark which is covered by the N1 actual needle. The N1 CMD is displayed only with the A/THR engaged.

R **ON A/C 106-149, 303-399, 401-499,
 G. N1 COMMAND The N1 CMD is displayed in analog form by means of four green arcs of circle joining the N1 actual needle to the N1 command needle. The N1 CMD is displayed only with the A/THR engaged, and the N1 CMD value valid, and engine running.
 1EFF : ALL 1 31-66-00Page 9 1 1 Aug 01/05 1 1 1CES 1

 N1 LIM mode selection and display
 Figure 006

R 1EFF : 106-149, 303-399, 401-499, 1 31-66-00Page 10 1 1 Aug 01/05 1 1 1CES 1

 N1 LIM mode selection and display
 Figure 007

R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 31-66-00Page 11 1201-299, 301-302, 1May 01/05 1 1 1CES 1

 H. N1 Trend In addition a green triangle next to the N1 CMD value enhences the N1 direction and stays displayed even when the two values are very close; it disappears when the N1 value has reached the N1 CMD value. It is displayed only if engine is running.
 J. N1 dgraded data In case of failure of the normal N1 measurement system from the FWC, the ECU computes a theoretical value taking into account the other engine parameters. In this case the last digit of N1 is dashed with two horizontal amber lines. (Ref. Fig. 008)
 **ON A/C ALL
 K. N2 INDICATION The N2 indications are displayed in the digital form only. 100% N2 correspond to 14460 RPM . Should N2 actual exceeds the N2 red line value , a red cross appears next to the digital indication to warn the pilot that an N2 exceeding has occurred. This red cross disappears only after a new take off or after a maintenance action through the MCDU . Like the N1, the N2 exceeding values are stored in the BITE memory and available on the MCDU through a maintenance menu.

R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
 L. EGT INDICATION The EGT indications are provided in the same form as for the N1 indications. The same applies concerning the changes in color and the EGT exceeding indications. However it has to be noticed that the amber line (EGT MAX) is variable; one value at engine start and another after (see values in paragraph ENGX parameters definition. In addition, at take off, the amber EGT limit is cancelled and the change in color of the needle is inhibited in the following cases:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 8(74)