3. Job Set-up
__________
Subtask 34-13-00-010-052
A. Get Access
(1)
Put the access platform in position at the access door 822.
(2)
Open the access door 822.
(3)
On the battery power center 105VU:
-
loosen the two screws and remove the protective cover.
Subtask 34-13-00-860-059
B.
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002). Subtask 34-13-00-865-064
C. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
Subtask 34-13-00-865-069
D. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/28VDC 5CC1 B04 105VU ELEC/CSM/G /EV AUTO/SPLY 7XE C01 121VU AUTO FLT/FAC2/28VDC 5CC2 M19
Subtask 34-13-00-860-061
E. Aircraft Maintenance Configuration
(1) Do the EIS start procedure (Ref. TASK 31-60-00-860-001).
R (2) Do the ADIRS start procedure (Ref. TASK 34-10-00-860-002), R
1EFF : ALL 1 34-13-00Page 507 1 1 May 01/05 1 1 1CES 1 1EFF : ALL 1 34-13-00Page 508 1 1 May 01/05 1 1 1CES 1
R R R (3) On the overhead panel : - on the FLT CTL panels 23VU and 24VU, make sure that the FAC, ELAC and SEC pushbutton switches are not pushed (in). The OFF legends are on. - on the ADIRS CDU, on the panel 20VU, make sure that the 3 OFF/NAV/ATT selector switches are at NAV, - on the ELEC panel 35VU, make sure that the battery voltage is correct, between 26VDC and 30VDC.
R R (4) On the center pedestal, on one MCDU, get the SYSTEM REPORT/TEST/NAV page (Ref. TASK 31-32-00-860-010).
(5) Make sure that the L/G doors are closed and the slats/flaps are fully retracted.
4. Procedure_________
Subtask 34-13-00-710-051
A. OVERSPEED Warning VMO/MMO 1 (L/G DOWN VMO/MMO SELECTION Switch 22FP at NORM)
NOTE : This test is for the VMO/MMO overspeed warning only. Ignore the____ warnings and indications (VLE, ...) which are not related to this test.
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
R R 1. On the overhead panel, on the ADIRS CDU: On the ADIRS DCU:
- push the ADR2 and ADR3 pushbutton switches. - the OFF legend of the ADR2 and ADR3pushbutton switches comes on.
2. On the MCDU: On the MCDU:
- push the line key adjacent to the ADR1 indication. - the ADR1 page comes into view.
- push the line key adjacent to the OUTPUT TESTS indication. - the ADR1 OUTPUT TESTS page comes intoview.
- push the line key adjacent to the INTERFACE TEST indication. - the ADR1 INTERFACE TEST 1/2 pagecomes into view.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R - on the keyboard push the NEXT R PAGE function key.
-
push the line key adjacent to the START TEST indication.
-
push the line key adjacent to the RETURN indication.
