(1)
Install the protective cover on the battery power center 105VU.
(2)
Tighten the two screws.
(3)
Close the access door 822.
1EFF : ALL 1 34-13-00Page 528 1 1 May 01/04R 1 1 1CES 1
(4) Remove the access platform(s). R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 34-13-00-865-076
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CC1, 5CC2, 7XE
**ON A/C ALL
Subtask 34-13-00-860-071
C. Put the aircraft back to its initial configuration.
(1)
On the MCDU, push the line key adjacent to the RETURN indication until the CFDS menu page comes into view.
(2)
Do the ADIRS stop procedure (Ref. TASK 34-10-00-860-005).
(3)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 34-13-00Page 529 1 1 Aug 01/05 1 1 1CES 1
TASK 34-13-00-710-006 Operational Test of the AOA SENSOR TEST WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______ YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
1. Reason for the Job__________________
This test controls the angle of attack (AOA) sensors to the special test
position.
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
34-10-00-710-007 Test of the Angle of Attack Warning
3. Job Set-up
__________ Subtask 34-13-00-860-073
A. Not Applicable
4. Procedure
_________ Subtask 34-13-00-710-060
A. Refer to the operational test of the angle of attack warning.
(Ref. TASK 34-10-00-710-007)
R 1EFF : ALL 1 34-13-00Page 530 1 1 Nov 01/00 1 1 1CES 1 TASK 34-13-00-710-007
Operational Test of the Overspeed Warnings in the Slats/Flaps and Landing Gear Extended (VFE/VLE) Configuration
NOTE : This test is for the system 1. For the systems 2 and 3, use the
____
indications between parentheses.
1. Reason for the Job
__________________
Refer to the MPD TASK: 341300-03
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 29-10-00-863-001 Pressurize the Green Hydraulic System 29-10-00-863-002 Pressurize the Yellow Hydraulic System 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
Power Supply 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 31-32-00-860-010 Procedure to Get Access to the SYSTEM REPORT/TEST NAV
Page
31-60-00-860-001 EIS Start Procedure
31-60-00-860-002 EIS Stop Procedure
32-22-00-010-001 Nose Gear Doors - Ground Doors Opening
32-22-00-410-001 Nose Gear Doors - Ground Doors Closing
R 34-10-00-860-002 ADIRS Start Procedure
1EFF : ALL 1 34-13-00Page 531 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 34-10-00-860-005 ADIRS Stop Procedure
3. Job Set-up
__________
Subtask 34-13-00-860-050
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Make sure that the nose landing gear doors are closed (Ref. TASK 32-22-00-410-001).
