(2)
Do the EIS start procedure
FOR 11FP1
Lower ECAM DU and CAPT ND only
FOR 11FP2
Lower ECAM DU only
(Ref. TASK 31-60-00-860-001).
1EFF : ALL 1 34-11-18Page 501 1 1 Feb 01/98 1 1 1CES 1
(3) Do the ADIRS start procedure
FOR 11FP1
ADIRU 1 and 3 only
FOR 11FP2
ADIRU 2 only
(Ref. TASK 34-10-00-860-002).
Subtask 34-11-18-865-053
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 11FP1
49VU NAV PROBES/ADIRU1/115VAC 4FP1 F06
**ON A/C 001-049, 051-061, 101-105, 201-203,
121VU ADIRS/ADIRU/3/115VAC 4FP3 N06
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
121VU ADIRS/ADIRU/3/115VAC 4FP3 N05
**ON A/C ALL
122VU ANTI ICE/PROBES/1/TAT 1DA1 Z12 FOR 11FP2
**ON A/C 001-049, 051-061, 101-105, 201-203,
121VU ADIRS/ADIRU/2/115VAC 4FP2 N07
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
121VU ADIRS/ADIRU/2/115VAC 4FP2 N06
**ON A/C ALL
122VU ANTI ICE/PROBES/2/TAT 1DA2 Y15
1EFF : ALL 1 34-11-18Page 502 1 1 Aug 01/05 1 1 1CES 1
4. Procedure
_________ Subtask 34-11-18-710-051
A. Test of the TAT Sensor
(1) Operational test of the TAT sensor 11FP1:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the SWITCHING panel 8VU:
-
set the ECAM/ND XFR selector - the display of the lower ECAM DU switch to CAPT. moves to the CAPT ND.
-make sure that the SAT and TAT indications are shown at the bottom of the CAPT ND, on the left side.
-
set the AIR DATA selector switch - make sure that the SAT and TAT
to CAPT/3. indications stay in view on the CAPT ND.
-
set the ECAM/ND XFR and AIR DATA selector switches to NORM.
(2) Operational test of the TAT sensor 11FP2:
-Make sure that the SAT and TAT indications are shown at the bottom section of the lower ECAM DU, on the left side.
5. Close-up
________ Subtask 34-11-18-860-050
A. Put the aircraft back to its initial configuration.
(1)
Do the ADIRS Stop Procedure(Ref. TASK 34-10-00-860-005).
(2)
On the center pedestal,on the ECAM control panel, set the LOWER DISPLAY potentiometer to OFF.
(3)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 34-11-18Page 503 1 1 Feb 01/00R 1 1 1CES 1
SENSOR - ANGLE OF ATTACK (3FP1,3FP2,3FP3) - REMOVAL/INSTALLATION
________________________________________________________________
TASK 34-11-19-000-001
Removal of the Angle of Attack Sensor (3FP1, 3FP2, 3FP3)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 3.4 m (11 ft. 2 in.)
R
3. Job Set-up
__________
Subtask 34-11-19-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 3FP1
49VU ANTI ICE/PROBES/AOA/1 4DA1 D04 49VU ANTI ICE/PROBES/PHC/1 2DA1 D03 49VU ANTI ICE/PROBES/PITOT/1 3DA1 D02 49VU NAV PROBES/ADIRU 1/AND AOA 1/26VAC 5FP1 F07 49VU NAV PROBES/ADIRU1/115VAC 4FP1 F06
**ON A/C 001-049, 051-061, 101-105, 201-203,
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航1(88)
