2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 0.20 to 3.60 m.daN
 (2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
 (8.00
 to 75.00 lbf.ft) FRDH141 1 ADAPTER - TORQUE 98D49207527000 1 SUPPORT FRAME - APU

 B.
 Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 03-002 GB DEF-STAN 91-101
 LUBRICATING OIL TURBINE ENGINE SYNT BASE
 (Ref. 20-31-00) Material No. 07-020 AI TNA 007-10012
 IDENTIFICATION PAINT (Ref. 20-31-00) Material No. 07-560
 SECURING LACQUER (Ref. 20-31-00) Material No. 11-004 USA MIL-T-81533
 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
 (Ref. 20-31-00)  -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

Material No. 19-010 USA AMS 5687
 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
 (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
0 Auxiliary Power Unit 49-11-04 50 -010C 1 bolts 49-11-04 50 -070 2 rear APU mount-bracket 49-11-04 50 -060 3 FWD APU mount-bracket (LH) 49-11-04 50 -040 4 washer 49-11-04 50 -100 5 nut 49-11-04 50 -120 7 nut 49-11-04 50 -110 8 setscrew 49-11-04 50 -090 9 FWD APU mount-bracket (RH) 49-11-04 50 -050 21 generator 24-23-04 01 -010D 21 generator 24-23-04 01 -010E 22 preformed packing 24-23-04 01 -010D 22 preformed packing 24-23-04 01 -010E 23 seal plate 24-23-04 01 -040 24 nuts 24-23-04 01 -020A 25 seal 24-23-04 01 -010D 25 seal 24-23-04 01 -010E 26 countersunk screws 24-23-04 01 -030
 D. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
49-11-11-400-003 Installation of the Power Plant (APU) (APS 3200) 49-11-11-991-022 Fig. 201 49-11-11-991-017 Fig. 202 49-11-11-991-018 Fig. 203

 3. Job Set-up
__________ Subtask 49-11-11-941-055
 A. Preparation for Build-up
 (1)
 Remove the Auxiliary Power Unit (0) from the transport container.

 (2)
 Install the APU on the SUPPORT FRAME - APU (98D49207527000). (Ref. Fig. 201/TASK 49-11-11-991-022)

 4. Procedure
_________ Subtask 49-11-11-420-066
 A. Installation of the APU Mount-Brackets
 (1) Installation of the FWD left and the FWD right APU mount-brackets. (Ref. Fig. 202/TASK 49-11-11-991-017)
 (a)
 Carefully put the FWD APU mount-bracket (LH) (3) and the FWD APU mount-bracket (RH) (9) in position. Make sure that the spigot is correctly engaged in the APU.

 (b)
 Install the 4 bolts (1) at each of the mount-brackets.

 (c)
 TORQUE the bolts (1) to between 2.6 and 3.0 m.daN (19.17 and

 22.12 lbf.ft).

 (d)
 Safety with MISCELLANEOUS (Material No. 19-010).

 (e)
 Install one setscrew (8) at each of the FWD APU mount-brackets

 (3) and (9) and lock it in position with the nut (7).

 (f)
 Remove any contamination from the contact areas of the bonding strap.

 (g)
 Install one bonding strap (6) with a washer (4) and a nut (5) on each setscrew (8).

 (h)
 Apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-020) on the nuts (5) and (7) and the setscrews (8).

 APU on Support Frame
 Figure 201/TASK 49-11-11-991-022

 CES

 Mount Brackets
 Figure 202/TASK 49-11-11-991-017

 CES

 (2) Install the rear APU mount-bracket.
 (Ref. Fig. 202/TASK 49-11-11-991-017)

 (a)
 Carefully put the rear APU mount-bracket (2) in position on the rear mount pad.

 (b)
 Attach the rear APU mount-bracket (2) to the APU with the 4 bolts (1).

 (c)
 TORQUE the bolts (1) to between 2.6 and 3.0 m.daN (19.17 and

 22.12 lbf.ft) and safety with MISCELLANEOUS (Material No. 19-010).
 Subtask 49-11-11-420-067
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER2(20)