-------------------------------------------------------------------------------
REFERENCE DESIGNATION ------------------------------------------------------------------------------- -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
31-36-00-740-004 Update of the APU Hours and Cycles in the DMU after
APU, ECB or DMU Replacement
49-00-00-080-002 Removal of the APU Hoist Tool (GTCP 36-300)
49-00-00-480-002 Installation of the APU Hoist Tool (GTCP 36-300)
49-00-00-710-001 Self-Test of the ECB (59KD) (GTCP 36-300)
49-00-00-710-004 Operational Test of the APU (4005KM) (GTCP 36-300)
49-12-00-210-001 Detailed Inspection of APU Suspension Rods, Vibration
Isolator Structure incl. Brackets and visible Part of
Attachment Fittings (GTCP 36-300)
49-12-54-400-001 Installation of the APU Mount Brackets (4065KM,
4075KM, 4085KM) (GTCP 36-300)
49-17-41-000-001 Removal of the Drain Tank (GTCP 36-300)
49-17-41-400-001 Installation of the Drain Tank (GTCP 36-300)
49-51-42-000-001 Removal of the Surge/Bleed Duct (8049KM) (GTCP
36-300)
49-51-42-400-001 Installation of the Surge/Bleed Duct (8049KM) (GTCP
36-300)
49-52-41-000-001 Removal of the Oil-Cooler Outlet-Duct (8052KM) (GTCP
36-300)
49-52-41-400-001 Installation of the Oil-Cooler Outlet-Duct (8052KM)
(GTCP 36-300)
49-52-52-400-001 Installation of the Compartment Cooling Duct (8054KM)
(GTCP 36-300)
49-81-00-200-001 Detailed Visual Inspection of the Exhaust V-Clamp and
Portion of Exhaust Duct inside APU Compartment (GTCP
36-300)
49-81-00-200-002 Detailed Visual Inspection of the Sealing Ring
Coupling (GTCP 36-300)
49-81-00-200-003 Detailed Visual Inspection of the Weld Joint between
the Exhaust Duct and the Inlet Duct (GTCP 36-300)
49-81-41-000-001 Removal of the Exhaust Muffler (GTCP 36-300)
49-81-41-400-001 Installation of the Exhaust Muffler (GTCP 36-300)
49-90-00-600-001 Check Oil Level and Replenish (GTCP 36-300)
49-91-42-200-001 Check APU Magnetic Chip Detector (MCD) (GTCP 36-300)
52-41-00-010-001 Open the APU Doors for Access
52-41-00-410-001 Close the APU Doors after Access
52-41-21-400-001 Installation of the APU Access Door 315AL
52-41-22-400-001 Installation of the APU Access Door 316AR and the
related Door Mechanism
49-11-11-991-002 Fig. 401
49-11-11-991-004 Fig. 402
49-11-11-991-001 Fig. 403
**ON A/C 001-003, 051-061,
49-11-11-991-003 Fig. 404
R **ON A/C 062-099, 401-499,
49-11-11-991-003-A Fig. 404A
R **ON A/C 001-003, 051-099, 401-499,
3. Job Set-up
__________
Subtask 49-11-11-860-060
A. Aircraft Maintenance Configuration
(1)
Energize the ground service network
(Ref. TASK 24-42-00-861-001).
(2)
On the panel 25VU make sure that the APU MASTER SW p/bsw is OFF.
(3)
Put a warning notice in the cockpit to tell persons not to start the APU.
(4)
Make sure that the hydraulic systems are depressurized (Ref. TASK 29-00-00-864-001).
NOTE : The installation of the APU is also possible without a removal
____ of the access doors. However, a removal of the doors will:
-
make the access to the APU compartment better.
-
make the installation and use of the hoist tool easier.
-
reduce the risk of injury to the personal.
-
reduce the risk of damaging the doors with the maintenance platform.
(5) Make sure that the:
-the oil-cooler outlet duct is removed (Ref. TASK 49-52-41-000-001).
-exhaust muffler is disconnected and moved rearwards.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER2(28)
