_______ MAKE SURE THAT THE HOIST IS ASSEMBLED AND ATTACHED CORRECTLY BEFORE YOU PUT A LOAD ON IT. OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE HOIST. IF THE HOIST IS IN AN INCORRECT CONDITION THE LOAD CAN MOVE ACCIDENTALLY AND KILL PERSONS OR CAUSE INJURY.
(a)
Remove the APU mount nuts (47), (48) and (50).
(b)
Install the PROTECTOR - THREADS, APU MOUNTING BOLTS to the threads (41) of the rear APU mount and the vibration isolators.
(2) Removal of the APU from the APU mount vibration-isolators CAUTION : MAKE SURE THAT THE THREE ATTACHMENT NUTS ARE REMOVED AND
_______ THAT THE APU CAN MOVE DOWN FREELY. IF YOU DO NOT DO THIS, YOU CAN CAUSE DAMAGE TO THE TIE RODS WHEN YOU LOWER THE APU.
CAUTION : MAKE SURE THAT ALL PLUMBING IS FREE FROM OBSTRUCTION.
_______
(a) Remove the APU from the APU mount vibration-isolators and lower it carefully from the APU compartment.
(3) Attachment of the APU to the SUPPORT FRAME - APU. CAUTION : MAKE SURE THAT ALL PLUMBING IS FREE FROM OBSTRUCTION.
_______
(a)
Attach the APU to the APU SUPPORT FRAME - APU NOTE : Make sure that the pip-pins are fully engaged in the
____ brackets of the APU support frame and the APU. Make sure that the screw at the rear of the APU support frame is fully engaged in the attachment plate and the APU.
(b)
Disconnect the HOIST - MINILIFT from the APU (Ref. TASK 49-00-00-080-002).
(c)
Put a blanking cover on the APU exhaust flange. NOTE : If you will not install the APU, you must install the
____ components of the kit for the FLIGHT WITHOUT APU.
(4) Disconnection of Replacement Components
(a)
Remove the Generator (80) (Ref. TASK 24-23-51-000-001).
(b)
Remove the FWD and AFT APU mount brackets (46) and (42)
(Ref. TASK 49-12-54-000-001).
(c)
Remove the APU LP Switch 5030QM (Ref. TASK 28-22-14-000-001).
(d)
Remove the Compartment Cooling Duct (Ref. TASK 49-52-52-000-001). NOTE : Keep these parts into a container for replacement at the
____
new component.
R **ON A/C 001-003, 051-099, 401-499,
TASK 49-11-11-400-001
Installation of the Auxiliary Power Unit (APU) - 4005KM (GTCP 36-300)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific fiber-bristled brush
No specific warning notice
No specific container 1.0 l (0.2641 USgal)
No specific access platform 3.5 m (11 ft. 6 in.)
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00
to 75.00 lbf.ft) 98A49107504001 3 PROTECTOR - THREADS, APU MOUNTING BOLTS 98D49207527000 1 SUPPORT FRAME - APU
B.
Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific Material No. 03-002
Material No. 06-001A Material No. 07-020 Material No. 11-001 Material No. 15-005
lockwire-corrosion resistant steel 0.8 mm (0.032 in.) dia.GB DEF-STAN 91-101 LUBRICATING OIL TURBINE ENGINE SYNT BASE (Ref. 20-31-00)USA MIL-L-23398 SOLID FILM LUBRICANT AIR DRYING (Ref. 20-31-00)AI TNA 007-10012 IDENTIFICATION PAINT (Ref. 20-31-00)USA MIL-D-16791 TYPE I DETERGENT (Ref. 20-31-00)AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
20-21-11-911-001 20-28-00-912-004 21-00-00-100-001 21-00-00-615-001 21-00-00-615-002 24-23-51-400-001 Tightening Torques for Standard Threaded FastenersElectrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-Cleaning of Special Components in the Environmental Control System (ECS)Decontamination of the Environmental Control System (ECS) when the Temperature is below 24 deg.C (APU)Decontamination of the Environmental Control System (ECS) when the Temperature is above 24 deg.C (APU)Installation of the APU Generator 8XS
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER2(27)
