C. Test
(1) Do the BITE test of the HF system (Ref. AMM TASK 23-12-00-740-001). NOTE : Do this test for the VHF 3 only.
____
_______________
4. Fault Isolation
R **ON A/C 001-049, 051-061, 101-105,
A. If the BITE test gives the maintenance message VHF 3 : NO DATA FROM CONTROL SOURCE:
- replace the RMP-COM/NAV FREQ SEL, 2 (1RG2) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞23-13-00∞∞∞∞∞∞∞∞∞∞Page 211
May 01/05 CES (1) If the fault continues:
- do a check and repair the wiring of the COM 1 DATA OUTPUT signal, (from RMP 2 (1RG2) pins A/<P, <Q to the first terminal block) (Ref. ASM 23-13/02).
R **ON A/C 062-099, 106-149, 151-199, 201-299, 301-399, 401-499,
A. If the BITE test gives the maintenance message RMP1/2/3 (1RG1/2/3)/VHF3 (1RC3)
- replace the RMP-COM/NAV FREQ SEL, 2 (1RG2) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the COM 1 DATA OUTPUT signal, (from RMP 2 (1RG2) pins A/<P, <Q to the first terminal block) (Ref. ASM 23-13/02).
**ON A/C ALL
B. Do the test given in Para. 3.C.
TASK 23-13-00-810-811 Loss of the Tuning Data for the HF 1 System
1. Possible Causes
_______________
- XCVR-HF, 1 (3RE1)
- RMP-COM/NAV FREQ SEL, 1 (1RG1)
- wiring (from the HF1 transceiver (3RE1) to the RMP1 (1RG1))
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 23-11-00-740-001 Bite Test of the HF System
AMM 23-11-33-000-001 Removal of the HF Transceiver (3RE1, 3RE2)
AMM 23-11-33-400-001 Installation of the HF Transceiver (3RE1, 3RE2)
AMM 23-13-13-000-001 Removal of the Radio Management Panel (CRMP) (1RG1,
1RG2, 1RG3) AMM 23-13-13-400-001 Installation of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) ASM 23-13/02
3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU COM/RMP/1 2RG1 G10
B. Job Set-up
On the RMP 1 only, make sure that the ON/OFF switch is at ON.
C. Test
(1) Do the BITE test of the HF system (Ref. AMM TASK 23-11-00-740-001). NOTE : Do this test for the HF 1 only.
____
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞23-13-00∞∞∞∞∞∞∞∞∞∞Page 213
May 01/04R
CES 4. Fault Isolation
_______________
A. If the BITE test gives the maintenance message RMP1/2/3 (1RG1/2/3)/HF1 (3RE1)
- replace the XCVR-HF, 1 (3RE1) (Ref. AMM TASK 23-11-33-000-001) and (Ref. AMM TASK 23-11-33-400-001).
(1) If the fault continues:
- replace the RMP-COM/NAV FREQ SEL, 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
(2) If the fault continues:
- do a check and repair the wiring (from the HF1 transceiver (3RE1) to the RMP1 (1RG1)) of the FREQ SELECT INPUT PORT A signal (from pins AB/3E, 3F to pins A/p, q) (Ref. ASM 23-13/02).
R **ON A/C 051-099, 106-149, 201-299, 301-399, 401-499,
B. Do the test given in Para. 3.C.
**ON A/C ALL
TASK 23-13-00-810-812
Loss of the RMP 1 Data on the Bus 2 (HF 1 System Source)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 COMMUNICATIONS 通訊1(76)
