R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210, 301-399, 401-499,
TASK 23-13-00-810-814
Loss of the RMP 2 Data on the Bus 2 (HF 2 System Source)
1. Possible Causes
_______________
- RMP-COM/NAV FREQ SEL, 2 (1RG2)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 23-11-00-740-001 Bite Test of the HF System AMM 23-13-13-000-001 Removal of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) AMM 23-13-13-400-001 Installation of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) ASM 23-13/02
3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU COM NAV/RMP/2 2RG2 L02
B. Job Set-up
On the RMP 2 only, make sure that the ON/OFF switch is at ON.
C. Test
(1) Do the BITE test of the HF system (Ref. AMM TASK 23-11-00-740-001). NOTE : Do this test for the HF 2 only.
____
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-105, 151-199, ∞∞23-13-00∞∞∞∞∞∞∞∞∞∞Page 219
201-210, 301-399, 401-499, Aug 01/05 CES
4. Fault Isolation
_______________
A. If the BITE test gives the maintenance message RMP1/2/3 (1RG1/2/3)/HF2 (1RC2)
- replace the RMP-COM/NAV FREQ SEL, 2 (1RG2) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the COM 2 DATA OUTPUT signal (from RMP 2 (1RG2) pins A/r, s to the first terminal block) (Ref. ASM 23-13/02).
R **ON A/C 051-099, 201-210, 301-399, 401-499,
B. Do the test given in Para. 3.C.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-105, 151-199, ∞∞23-13-00∞∞∞∞∞∞∞∞∞∞Page 220
201-210, 301-399, 401-499, Aug 01/05 CES
**ON A/C ALL
TASK 23-13-00-810-819 Loss of the Data from the RMP 3 to the RMP 1
1. Possible Causes
_______________
- RMP-COM/NAV FREQ SEL, 1 (1RG1)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 23-13-00-740-001 BITE Test of the Radio Management AMM 23-13-13-000-001 Removal of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) AMM 23-13-13-400-001 Installation of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) ASM 23-13/01
3. Fault Confirmation
__________________
A. Job Set-up On the RMP 1 and RMP 3 only, make sure that the ON/OFF switches are at ON.
B. Test
(1) Do the BITE test of the Radio Management (Ref. AMM TASK 23-13-00-740-001).
NOTE : Do this test for the RMP 1 only.
____
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞23-13-00∞∞∞∞∞∞∞∞∞∞Page 221
May 01/99R
CES 4. Fault Isolation
_______________
**ON A/C 001-049, 051-061, 101-105,
A. If the test gives the maintenance message RMP 1 : NO DATA FROM RMP 3:
- replace the RMP-COM/NAV FREQ SEL, 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the DIALOGUE INPUT signal, (from RMP 1 (1RG1) pins A/<Z, AA to the first terminal block) (Ref. ASM 23-13/01).
R **ON A/C 062-099, 106-149, 151-199, 201-299, 301-399, 401-499,
A. If the test gives the maintenance message RMP3(1RG3)/RMP1(1RG1):
- replace the RMP-COM/NAV FREQ SEL, 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the DIALOGUE INPUT signal, (from RMP 1 (1RG1) pins A/<Z, AA to the first terminal block) (Ref. ASM 23-13/01).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 COMMUNICATIONS 通訊1(78)
