- replace the RMP 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
R **ON A/C 062-099, 106-149, 151-199, 201-299, 301-399, 401-499,
B. If the tests give these two maintenance messages
RMP1(1RG1)/RMP2(1RG2)
RMP1(1RG1)/RMP3(1RG3):
- do a check of the circuit breaker (2RG1) status.
(1) If the circuit breaker (2RG1) is closed:
- do a check for 28VDC at pin A/N of the RMP 1 (1RG1) (Ref. ASM 23-13/01).
(a) If there is 28VDC:
- replace the RMP-COM/NAV FREQ SEL, 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
(b) If there is no 28VDC:
- do a check for a ground signal at pin A/R of the RMP 1 (1RG1) (Ref. ASM 23-13/01).
1 If there is no ground signal:
_
- repair the wiring between the RMP 1 (1RG1) pin A/R and the ground terminal (Ref. ASM 23-13/01).
2 If there is a ground signal:
_
- do a check of the wiring between the RMP 1 pin A/N and the circuit breaker (2RG1) (Ref. ASM 23-13/01).
a If there is no continuity:
_ - repair the above wiring.
b If there is continuity:
_
- replace the circuit breaker (2RG1).
(2) If the circuit breaker (2RG1) is open:
- close it.
(a) If it opens again:
- replace the RMP 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
1 If the fault continues:
_
- do a check for a short to ground at the wiring between the RMP 1 (1RG1) pin A/N and the circuit breaker (2RG1) (Ref. ASM 23-13/01).
a If there is a short to ground:
_ - repair the related wiring.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞23-13-00∞∞∞∞∞∞∞∞∞∞Page 231
Aug 01/05 CES
R b_ If there is no short to ground:
R - replace the C/B-COM/RMP/1 (2RG1).
R (b) If the circuit breaker stays closed and the fault continues:
R - replace the RMP 1 (1RG1) (Ref. AMM TASK 23-13-13-000-001) and
R (Ref. AMM TASK 23-13-13-400-001).
R **ON A/C ALL
C. Do the tests given in Para. 3.B.
TASK 23-13-00-810-825
Failure of the RMP 2 (RMP 1 and RMP 3 Sources)
1. Possible Causes
_______________
- RMP-COM/NAV FREQ SEL, 2 (1RG2)
- wiring
- C/B-COM NAV/RMP/2 (2RG2)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 23-13-00-740-001 BITE Test of the Radio Management AMM 23-13-13-000-001 Removal of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) AMM 23-13-13-400-001 Installation of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) ASM 23-13/01
3. Fault Confirmation
__________________
A. Job Set-Up On the RMP 1, RMP 2 and RMP 3, make sure that the ON/OFF switches are at ON.
B. Test Do the BITE test of the Radio Management (Ref. AMM TASK 23-13-00-740-001).
NOTE : Do this test for the RMP 1 and RMP 3 only.
____
4. Fault Isolation
_______________
A. Table of the circuit breakers used in this procedure:
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 COMMUNICATIONS 通訊1(81)
