C64976
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C01B Page 413 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Prepare For the Removal of the Power Plant
__________________________________________
 Prepare the Airplane for the Removal of the Power Plant

 (a)  
Disconnect the left and right opening actuators at the lower end.

 (b)  
Open the return valve on the hand pump.

 (c)  
Retract the actuator until it is clear of the fuel outlet line at the fuel flow transmitter.

 (d)  
Attach the lower end of the opening actuators to the thrust reverser.

 S 434-019-C00
 (20)
 Apply tape around the edge of the thrust reverser so that the latches are in the closed position (Fig. 402A).

 (a)  
This will give clearance for the transportation base and cradle assembly.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C01B Page 414 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEEA
THRUST REVERSER LATCHES
THRUST REVERSER LATCH
TAPE
 FWD
A

Application of Tape on Thrust Reverser Latches
Figure 402A

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C01B Page 415 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E37743
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Prepare For the Removal of the Power Plant
__________________________________________ Engine Core Disconnects on the Right Side
 H.  Engine Core Disconnects on the Right Side
 S 034-221-C00
 (1)
Do these steps to disconnect the W1508 core wire bundle (Fig. 403):

 (a)  
Disconnect the electrical connectors at the pressure regulating and shutoff valve (PRSOV) bracket as follows:

 NOTE: To make the installation easier, keep the clamps
____ attached to the wire bundle.
 1)  ENGINES WITHOUT THE CAPTIVE FASTENER CLAMPS; Release the clamp (1), bolt (2), washer (3), and nut (4) that attach the wire bundle to the forward end of the precooler.
 2)  ENGINES WITH THE CAPTIVE FASTENER CLAMPS; Release the clamp (5) that attaches the wire bundle to the forward end of the precooler.
 3) Remove the three bolts (9 and 10) and washers (11) that attach the top bracket to the bottom bracket. 4) Disconnect the electrical connectors D1208 and D1210.
 CAUTION: MAKE SURE YOU INSTALL CAPS ON THE ELECTRICAL
_______ CONNECTORS. IF YOU DO NOT INSTALL CAPS ON THE ELECTRICAL CONNECTORS, CONTAMINATION OF THE CONNECTORS CAN OCCUR.
 5) Install caps on the end of each electrical connector. 6) Move the wire bundle connectors away from the PRSOV. This will give clearance when you remove the engine.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-00-02
 ALL  ú ú C11B Page 416 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE A
PRECOOLER
1.
 CLAMP

2.
 BOLT

3.
 WASHER

4.
 NUT

1
ELECTRICAL
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(112)