(2)
AMM 22-31-11/501, Autothrottle PLA Sychro
(3)
AMM 27-81-00/201, Leading Edge Flap and Slat Control System
(4)
AMM 54-32-01/401, Forward Fairing
(5)
AMM 71-00-00/501, Power Plant
(6)
AMM 71-00-03/201, Engine Depreservation
(7)
AMM 71-11-02/401, Fan Cowl Panels
(8)
AMM 71-21-00/601, Engine Mounts
(9)
AMM 71-21-01/401, Engine Mount Cone Bolts
(10)
AMM 76-11-00/501, Engine Control System
(11)
AMM 78-31-00/201, Thrust Reverser System
(12)
AMM 79-31-00/501, Oil Quantity Indicating System
F.
Access
(1)
Location Zones
506 Engine No. 1
606 Engine No. 2
(2)
Access Panels
5739L/5733L Thrust Reversers - Engine No. 1
5839R/5838R Thrust Reversers - Engine No. 2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-02
ALL ú ú C03B Page 480V ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Put the Airplane Back To Its Usual Condition
____________________________________________ Core Area Connections on the Left Side
G. Core Area Connections on the Left Side
S 434-086-C00
(1) Connect the PRSOV downstream sense line to the PRSOV as follows (Fig. 405):
NOTE: Connect this sense line before you install the PRSOV.
____ The access to this PRSOV port is easier if the PRSOV is not installed.
(a)
Apply antiseize compound to the threads on the union.
(b)
Connect the PRSOV downstream sense line to the union on the left side of the PRSOV.
S 434-087-C00
(2) Attach the PRSOV to the engine between the precooler and the 5th-stage duct as follows:
(a)
Lift the PRSOV until it is between the duct and the precooler.
(b)
Loosely install the duct couplings (1).
NOTE: It may be necessary to loosen couplings on the
____ 5th-stage duct forward of the valve to get clearance between the PRSOV and the precooler for engine installation.
(c)
Turn the PRSOV to the correct position that you marked in the removal procedure.
(d)
Make a check of the clearance between the engine flange and the PRSOV as follows: 1) ENGINES WITHOUT THE VIBRATION ISOLATORS FOR THE FORWARD
MOUNT/THRUST REVERSER HINGES;
The minimum clearance is 1.3-1.7 inch (33.0-43.2 mm).
2) ENGINES WITH THE VIBRATION ISOLATORS FOR THE FORWARD MOUNT/THRUST REVERSER HINGES; The minimum clearance is 0.9-1.3 inch (22.9-33.0 mm).
(e) Tighten the duct couplings to 95-110 pound-inches (10.7-12.4 Newton meters).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-02
ALL ú ú C06B Page 480W ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Put the Airplane Back To Its Usual Condition
____________________________________________ Core Area Connections on the Right Side
H. Core Area Connections on the Right Side
S 434-088-C00
(1)
Do these steps to attach the fire extinquishing hose and the pneumatic overtemperature sense hose to the engine (Fig. 404):
(a)
ENGINES WITHOUT THE QUARTER TURN CLAMP; Install the fire extinquishing hose to the fan air duct with the clamp (4), washer (5) and nut (6)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(142)
