(b)
Other Procedure
1) Drain the engine lubrication system. a) Drain the engine oil tank (AMM 12-13-11/301). b) Drain the accessory gearbox (AMM 12-13-11/301). c) Remove the scavenge oil filter element
(AMM 79-21-04/401). d) Put a container below the oil supply filter. e) Remove the filter drain plug and let the oil drain. f) Remove the magnetic chip detectors (AMM 79-21-05/201).
2) Let the oil fully drain.
3) Remove the oil drain adapter from the drain port of the oil tank. a) Push the adapter into the drain port while you turn it
counterclockwise. b) Pull the adapter down and remove it from the drain port. 4) Install the drain plug in the oil tank. a) Lubricate a new O-ring with engine oil and install it on the drain plug.
CAUTION: DO NOT CAUSE DAMAGE TO THE O-RING DURING THE
_______ INSTALLATION. IF YOU CAUSE DAMAGE TO THE O-RING, OIL LEAKAGE CAN OCCUR.
b) Carefully install the drain plug into the drain port of the oil tank. c) Push the plug into the drain port and turn it clockwise until the locking pins are fully engaged. 5) Install the drain plug into the accessory gearbox. a) Lubricate a new O-ring with engine oil and install it on the drain plug.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-03
ALL ú ú C03 Page 223 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
6) 7)
8) 9)
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
b) Lightly lubricate the threads of the gearbox drain plug with engine oil.
c) Install the drain plug.
d) Tighten the plug to 180-200 pound-inches (20.3-22.6 Newton meters).
e) Safety the plug with a lockwire.
Install the scavenge oil filter element (AMM 79-21-04/401).
Install the drain plug for the oil supply filter.
a) Lubricate the new O-ring with engine oil and install it on the drain plug.
b) Install the drain plug.
c) Tighten the plug to 43-48 pound-inches (4.9-5.4 Newton meters).
d) Safety the plug with a lockwire.
Install the magnetic chip detectors (AMM 79-21-05/201).
Do the preservation procedure for the engine lubrication
system.
a) Use a cart or a hand pump with a volume measuring device to fill the locations that follow with one of these mixtures at a maximum pressure of 50 psi (345 kPa):
-
Engine oil and 5 percent by volume of preservative
oil (CP2259) or
-
Engine oil and 7 percent by volume of anti-corrosion
oil additive (CP2039).
Location________ Oil Quantity
Oil supply to accessory gearbox 6 quarts (6 liters)
Oil supply to forward sump 2 quarts (2 liters)
Oil supply to aft sump 1 quart (1 liter)
Oil tank 20 quarts (19 liters)
Lube unit Wet parts
Oil supply to scavenge oil filter 0.5 pint (0.24 liter)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
71-00-03
ALL ú ú C01 Page 224 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
b) Install caps on all lube system ports, tube openings, drains, and vents to seal the lube system.
S 432-060-C00
(7)
Make sure all disconnected lines and electrical connections have caps on them.
S 432-061-C00
(8)
Seal the inlet and exhaust openings with the vapor barrier film.
(a) Attach the vapor barrier film with tape.
S 432-062-C00
(9) Put the desiccant on one side of the engine, but do not let it touch the engine hardware.
NOTE: The dessicant must be replaced at regular intervals based on
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(160)
