(1)  
AMM 71-00-00/201, Power Plant

 (2)  
AMM 71-00-01/201, Power Plant-Trim Tables

 (3)  
AMM 71-00-02/401, Power Plant

 (4)  
AMM 72-31-00/501, Fan and Booster

 (5)  
AMM 77-31-00/201, Airborne Vibration Monitoring (AVM) System

 (6)  
AMM 77-31-03/401, Signal Conditioner

 D.
Access

 (1)  
Location Zones
 506 Engine No. 1
 606 Engine No. 2

 (2)  
Access Panels
 5737L/5837R Fan Cowl Assy
 5746L/5846R Fan Cowl Assy
 5738L/5838R Thrust Reverser Cowl Assy
 5739L/5839R Thrust Reverser Cowl Assy

 E.
Procedure

 (1)  
Do the Vibration Survey

 S 735-014-C00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 71-00-00
 ALL  ú ú C10 Page 559 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TEST NO. 7 - VIBRATION SURVEY
_____________________________
 CAUTION:_______ OPERATE THE CFM56-3-B1 ENGINES AT CFM56-3B-2 POWER
 POSITIONS IN THIS PROCEDURE ONLY.  THE CONTINUOUS
 OPERATION OF THE CFM56-3-B1 ENGINES AT THE CFM56-3B-2
 TAKEOFF POWER POSITIONS WILL CAUSE ENGINE PERFORMANCE
 DETERIORATION.

 CAUTION: DO NOT USE THE TOTAL TEMPERATURE INDICATION FROM THE
_______ AIRPLANE FOR THE AMBIENT AIR TEMPERATURE. MAKE SURE THAT YOU GET THE LOCAL BAROMETRIC PRESSURE (NOT CORRECTED TO SEA LEVEL) FROM THE CONTROL TOWER. THIS WILL PREVENT AN INCORRECT TRIM TARGET SELECTION.
 DO NOT PUT A MERCURY THERMOMETER ON THE AIRPLANE. MERCURY (FROM A BROKEN THERMOMETER) CAN CAUSE DAMAGE TO THE AIRPLANE COMPONENTS.
 (a)  Find and make a record of these conditions:
 1)  Make a record of the ambient air temperature (outside air temperature (OAT)) in the shade of the wheel well of the nose gear.
 2)  Make a record of the barometric pressure.
 (b)  
Find and make a record of the static takeoff (T.O.) power position for the current OAT and barometric pressure. 1) Look at the STATIC T.O. PMC ON/OFF trim data

 (AMM 71-00-01/201).

 (c)  
If it is available, install the test equipment for the engine vibration isolation (Fig. 509). 1) On the circuit breaker panel, P6, open the ENG VIB MON

 circuit breaker.
 2) Remove the AVM signal conditioner from the main E/E rack (AMM 77-31-03/401). 3) Put the signal conditioner on the floor. 4) Connect the connector (J1) to the test equipment unit on
 the electronic shelf connector (D3228). 5) Connect the connector (P1) on the test equipment unit to the signal conditioner. 6) Connect the selector switch to the electrical connector (J2) on the test equipment unit.
 7)  Open the access door above the main E/E rack. a) Put the selector switch in the flight compartment. b) Put the switch in the COMMON position.
 8)  Close the ENG VIB MON circuit breaker.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 71-00-00
 ALL  ú ú C09 Page 560 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
RACK, E1 EQUIPMENT ELECTRONIC 
SEE  C  SHELF 1 
SEE  A  SEE  B  DIGITAL ANALOG ADAPTER NO.1 (REF)  DIGITAL ANALOG ADAPTER (REF) NO.2 
TEST EQUIPMENT UNIT A  SHELF 2
TEST EQUIPMENT UNIT 
CONDITIONER AVM SIGNAL B 

SELECTOR SWITCH
C
Engine Vibration Isolation Test Equipment Figure 509
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 71-00-00
 ALL  ú ú C09 Page 561 ú Mar 12/00
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 動力裝置 POWER PLANT 1(72)