Figure 819

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-11-00
 ALL  ú ú 01 Page 843 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A14713
A
747-400 MAINTENANCE MANUAL
 F. Procedure
 S 028-057
 (1)  Remove the seal from the door fully.
 NOTE: If the seal cannot be removed from the cast aluminum access
____ panel the access panel does not have a molded rubber seal that you can remove and replace. You must replace the full access panel. Only new cast aluminum access panels have molded rubber seals you can remove and replace.
 S 148-058
 CAUTION: DO NOT CAUSE DAMAGE TO THE FINISH WHEN YOU REMOVE THE SEALANT.
_______
 TOO MUCH FORCE CAN REMOVE THE PAINT OR PRIMER.

 (2)  
Remove the remaining sealant from the seal groove with the sealant removal tool.

 S 128-059

 (3)  
Clean the seal carefully before you install it.

 (a)  
Rub the seal with the sandpaper to remove the parting agent.

 NOTE: Rub carefully to make sure that the seal bonds to the
____
 groove.

 (b)  
Remove the unwanted material with the aliphatic naphtha.

 (c)  
Clean the seal with the methyl ethyl ketone, acetone, isopropyl alcohol, or ethyl alcohol and dry it.

 S 398-060
 (4)  Prepare the seal groove.
 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON
_______ YOUR SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (a)  
Clean the seal groove with a clean wiper moistened with Series 93 solvent (AMM 20-30-93/201).

 (b)  
Dry the seal groove with the air gun.

 (c)  
Rub the groove with a wiper lightly moistened with Series 93 solvent (AMM 20-30-93/201).

 (d)  
Apply the BMS 5-26 Type II Class A (or Proseal 860, B 1/6) sealant to the full width of the seal groove.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-11-00
 ALL  ú ú 03 Page 844 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 428-061
 (5)  Install the seal and make sure it is tightly against the seal groove in all positions.
 TASK 28-11-00-308-203
 7.  Approved Repair of the Secondary Fuel Barrier Sealant_____________________________________________________
 A. General
 (1)  
If there is leakage in the secondary fuel barrier, the leakage must be repaired before the airplane is released for flight.

 (2)  
Secondary fuel barrier sealant is a polyurethane (Type II) material applied to the upper exterior surface of center auxiliary fuel tank.

 B.
Equipment

 (1)  
Brush - Paint

 (2)  
Instrument - Dualscope Thickness Measurement, Model MP20 9U437 Fischer Technology Inc. 750 Marshall Phelps Road, Windsor CT 06095-2199

 (3)  
Probe - Thickness Measurement, Pencil - Type, Model ETA3.3H 9U437 Fischer Technology Inc. 750 Marshall Phelps Road, Windsor CT 06095-2199

 C.
Consumable Materials

 (1)  
G02088 Abrasive, silicon carbide, waterproof
 paper - P-P-101

 (2)  
G00034 Cheesecloth, gauze - BMS 15-5

 (3)  
B00184 Cleaning Solvent - BMS 11-7

 (4)  
C00259 Primer - BMS 10-11, Type I (yellow)

 (5)  
A00015 Sealant, secondary fuel barrier -BMS 5-81, Type II

 (6)  
A00767 Sealant, Integral Fuel Tank BMS 5-45

 (7)  
A00955 Sealant, BMS 5-26, Type II

 (8)  
G00215 Flat, bristle brush

 D.
References

 (1)  
AMM 51-21-02/701, Prepaint Cleaning and Treatment

 E.
Access

 (1)  
Location Zones
 131 Center Section Wing Box (Left)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 1(107)