EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-16-05
 ALL  ú ú 01 Page 404 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 E. Procedure
 S 014-015
 (1)  
Open the necessary access panel for the inboard aileron actuator, 573AB or 673AB.

 S 984-016

 (2)  
Use the manual override lever to put the valve actuator in the closed position.

 S 434-017

 (3)  
Go into the inboard main tank.

 S 434-034

 (4)
Engage the valve body with the adapter shaft that has splines.

 S 434-035

 (5)  
Make sure the shaft and the valve index marks align.

 S 424-036

 (6)  
Install the gasket seal on the valve body flange and hold the valve body into its position on the tank end rib.

 S 424-018

 (7)  
Go into the outboard main tank and install the gasket seal and the inlet tube on the tank end rib.

 S 434-019

 (8)  
Install the bolts and the washers (6 locations) that attach the tube to the tank end rib.

 (a)  
Tighten the bolts.

 S 434-020
 (9)  
Connect the bonding jumper for the inlet tube to the structure (AMM 20-11-15/401).

 S 434-021

 (10)
 Go into the inboard main tank and install the valve support ring and the support clamp.

 (a)  
Tighten the clamp bolts.

 (11)
 Install the new O-ring in the coupling for the outlet tube.

 S 434-022
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-16-05
 ALL  ú ú 01 Page 405 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 434-040
 (12)
 Put the outlet tube into a position that points to the bottom of the fuel tank.

 S 434-037

 (13)
 Connect the coupling to the valve body.

 (a)  
Put a lockwire through the coupling and the tab on the valve body.

 S 434-023
 (14)
 Install the support clamp for the outlet tube.

 (a)  
Tighten the clamp bolts.

 S 434-024
 (15)
 Connect the bonding jumper for the outlet tube to the structure (AMM 20-11-15/401).

 S 434-025

 (16)
 Connect the bonding jumper to the valve body (AMM 20-11-15/401).

 S 764-041

 (17)
 Meaure the resistance values for the subsequent:

 (a)  
The valve body and the airplane structure.

 (b)  
The tubes and the airplane structure (AMM 20-22-01/601). 1) The resistance values can not be more than 0.010 ohm.

 S 864-027
 (18)
 Get out of the fuel tank.

 S 414-039

 (19)
 Close the access door for the fuel tank (AMM 28-11-00/201).

 S 414-028

 (20)
 Close the access panel for the inboard aileron actuator, 573AB or 673AB.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-16-05
 ALL  ú ú 01 Page 406 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 MAIN TANK TRANSFER VALVE ADAPTER - REMOVAL/INSTALLATION
_______________________________________________________
 1.  General_______
 A.  This procedure contains instructions for the removal and installation of the adapter for the transfer valve assembly in the main tank.
 B.  Two persons are necessary for these tasks: one person out of the fuel tank to pull or push the adapter shaft through the spar opening and to hold the adapter plate; and one person in the fuel tank to remove or install the hardware that is installed.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 1(194)