28-11-00
ALL ú ú 02 Page 726 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b) To apply the alodine solution, do the steps that follow:
1) Remove all burrs or particles from the surface and make nicks or scratches smooth.
WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR
_______ YOUR SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
2) Clean the surfaces with solvent, Series 88 solvent.
3) Apply alodine solution to the cleaned metal surface with a Scraper brush, swab, spray gun, swatches of soaked blotting paper, or a clean cellulose sponge.
NOTE: If the alodine solution does not apply smoothly, the
____ metal surface is not cleaned correctly.
4) Keep the surface continuously moist with the alodine solution until a layer is made.
NOTE:____It can take 1 to 5 minutes to make a layer. The time is related to the temperature.
5) Flush with clean water or carefully rub with soft cloths or sponges to remove unwanted alodine solution.
H. Apply the Corrosion Resistant Finish (Topcoat)
S 627-208
WARNING: HAVE A GOOD FLOW OF AIR IN THE AREA THAT YOU APPLY THE
_______ CORROSION RESISTANT FINISH (TOPCOAT). DO NOT GET THE CORROSION RESISTANT FINISH IN YOUR MOUTH OR EYES, OR ON YOUR SKIN. PUT ON A PROTECTIVE SPLASH GOGGLE AND GLOVES WHEN YOU USE THE CORROSION RESISTANT FINISH. KEEP THE CORROSION RESISTANT FINISH AWAY FROM SPARKS, FLAME AND HEAT. THE CORROSION RESISTANT FINISH IS A POISONOUS AND FLAMMABLE COMPOUND WHICH CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1)
To mix the corrosion resistant finish, do the steps that follow:
(a)
Make sure the materials are at 60° to 90° F (15.6° to 32.2° C) before you mix them.
(b)
Shake the base component for 10 minutes in a shaker.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-11-00
ALL ú ú 02 Page 727 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(c)
Measure proportional volumes of base and catalyst, and reducer or thinner if you want to apply the corrosion resistant finish with a spray gun, refer to the table below (Table 701) .
(d)
Mix the base and the catalyst.
(e)
Add a reducer if it is necessary.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-11-00
ALL ú ú 02 Page 728 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
~.............................................................................. | | | METHOD OF APPLICATION | | | ......................................................... | | | SPRAY | BRUSH | | | ......................................................... | | | | |VISCOSITY | |PARTS | | | |MANUFACTURER| PARTS |ZAHN NO. 1 |MANUFACTURER |BY | |MANUFACTURER|COMPONENT|DESIGNATION |BY VOLUME|72° | 2°F |DESIGNATION |VOLUME| ................................................................................ |Bostik West |Base |454-1 | 3 |31-40 |454-1 | 3 | |(BMS 10-20, |Catalyst |CA109 | 1 |seconds |CA-109 | 1 | |Type II) |Reducer |TL-52 |approx 1 | | | | ................................................................................ |Desoto |Base |823-011 | 4 |31-40 |823-011 | 4 | |(MIL-C-|Activator|910-099 | 1 |seconds |910-099 | 1 | | 27725) |Reducer |020-037 |approx 4 | |020-037 | 0-4 | | | | | | | | | | |Base |823-730 | 4 |31-40 |823-730 | 4 | | |Activator|910-702 | 1 |seconds |910-702 | 1 | | |Reducer |020-707 |approx 4 | |020-707 | 0-4 | ................................................................................ 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 1(90)
