(b)
Do a visual inspection of the component interface and/or the adjacent area.
(c)
Unwind 100 mm (3.9370 in.) of the new self-adhesive film from the roll and remove the protective paper.
(d)
Align the self-adhesive film (2) to the GFRP (5) and install it with a soft cotton cloth MISCELLANEOUS (Material No. 19-003) and a light pressure of your hand. Work from the middle of the self-adhesive film (2) towards the sides.
(e)
With a ROLLER - RUBBER press down the self-adhesive film (2) onto the GFRP (5).
NOTE : Move the rubber roller backwards and forwards and around
____
the edges for a better bond.
(f) Do the steps (4)(c) thru (e) until you have installed all of the GFRP (5) with the adhesive film (2).
R EFF : 001-049, 051-099, 101-105, 151-156, 25-28-42Page 427 201-209, May 01/05
CES Subtask 25-28-42-160-052
D. Preparation of the Seat Tracks and the Floor Panels for the Installation of the NTF-Covering. (Ref. Fig. 401/TASK 25-28-42-991-001, 402/TASK 25-28-42-991-006)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Preparation of the Seat Tracks (10):
(a)
Clean the component interface and/or the adjacent area. Use CLEANING AGENTS (Material No. 11-004). If necessary use a vacuum cleaner.
(b)
Do an inspection of the component interface and/or the adjacent area.
(c)
Apply adhesive-promoter SEALANTS (Material No. 09-028B) to the seat track (10).
NOTE : Add to previous step, where the sealant (7) will be
____
applied.
(d) Seal the seat tracks (10):
1 Cut the synthetic fibre-cord MISCELLANEOUS (Material No. 19-
_
002) (8) to the required length.
NOTE : The cord must be 50 mm (2 in.) longer than the area
____
that you will seal.
2 Make a loop at one end of each of the cords (8).
_
3 Put the cords (8) in the seat tracks (10).
_ NOTE : This step is to make the next removal procedure easier.
____
R EFF : 001-049, 051-099, 101-105, 151-156, 25-28-42Page 428 201-209, May 01/05
CES
4_ Apply SEALANTS (Material No. 09-016) (7) in the seat tracks
(10). Apply the sealant (7) only in the area of the adhesive
promoter in the seat tracks (10).
5 Push the loops into the sealant (7).
_
(2) Apply corrosion preventive compounds into the seat tracks (10):
(a)
Apply masking paper and masking tape around the seat tracks (10) where you will apply corrosion preventive compounds.
(b)
Apply the STORAGE PRESERVATION (Material No. 15-004) into the seat tracks (10).
(c)
Apply the STORAGE PRESERVATION (Material No. 15-008) into the seat tracks (10).
(d)
Apply the COMMON GREASE (Material No. 04-022) into the seat tracks (10).
(e)
Cut the section (9) to the required length and push it into the grease. Do this only in areas where persons walk and not in areas where furnishings will be installed.
(f)
Remove the unwanted grease with a SCRAPER - NON METALLIC. Do this at the top of the seat track (10) to get a flush surface.
NOTE : Make sure that the complete seat track (10) is filled with
____ COMMON GREASE (Material No. 04-022) where the adhesive foil (4) will be installed above the seat track (10).
(g) Remove the masking paper and masking tape from the floor panels.
(3) Preparation of the Floor Panel (6):
(a)
Make sure that the component is free from dust and particles. If necessary use a vacuum cleaner.
(b)
Clean the component interface and/or the adjacent area. Use CLEANING AGENTS (Material No. 11-004).
(c)
Do an inspection of the component interface and/or the adjacent area.
R EFF : 001-049, 051-099, 101-105, 151-156, 25-28-42Page 429 201-209, May 01/05
CES
(4) Installation of the adhesive tape (width 102.0 mm (4.02 in.)) (3) to the floor panels (6):
(a)
Unwind 100 mm (4.0 in.) of the new self adhesive tape BONDING AND ADHESIVE COMPOUNDS (Material No. 08-082) (3) from the roll and remove the protective paper.
(b)
Align the adhesive tape (3) to the floor panel (6) and install it with a soft cotton cloth and a light pressure of your hand.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(110)
