(b)
 Remove the cap (3), the screws (4) and (1) and the washers (2).

 (c)
 Carefully tilt the lining to remove the nuts (22) and the socket (23).

 (d)
 Remove the lining 222RW.

 EFF : ALL

25-23-45Page 419
May 01/05
R
 CES  TASK 25-23-45-400-007

 Installation of the Door Frame Linings at the Right FWD Passenger/Crew Door
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
11-00-00-400-002 Installation of the Decals 20-21-11-911-001 Tightening Torques for Standard Threaded Fasteners 24-42-00-861-001 Energize the Ground Service Network from the External
 Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from
 the External Power
 33-51-11-400-001 Installation of the Cabin Emergency Light
 33-51-13-400-001 Installation of the Cabin Wall-Mounted

 Emergency-Exit-Markers
 33-51-16-400-001 Installation of the Emergency Exit Sign

R  35-23-00-710-001 Operational Check of Manual Mask Release 52-10-00-410-001 Closing of the Passenger/Crew Door AMM 11-32-25 P.Block 001 INTERIOR PLACARDS (SEE ALSO 11-42-25) 25-23-45-991-003-A Fig. 402
 EFF : ALL

25-23-45Page 420

 3. Job Set-up
__________
 Subtask 25-23-45-860-051

 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001)

 (2)
 Clean the component interface and/or the adjacent area.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 Subtask 25-23-45-865-057
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL SERVICE IDENT. LOCATION -------------------------------------------------------------------------------2000VU VACUUM CLEANER SOCKET-CABIN Z222 1ME A03
 4. Procedure
_________
 Subtask 25-23-45-420-058-A

 A. Installation of the door frame linings 222RW, 222SW, 222TW, 222UW, 222VW
 (Ref. Fig. 402/TASK 25-23-45-991-003-A) R
R (1) Unless specified, TORQUE all nuts, bolts and screws (Ref. TASK 20-21-11-911-001).
R (2) Install the lining 222RW:
 (a)
 Put the socket (23) in position and install the nuts (22).

 (b)
 Put the the lining 222RW in position.

 (c)
 Install the screws (1), (4) and the washers (2), but do not tighten the screws (1) and (4).

 EFF : ALL

25-23-45Page 421

 (d) Install the handgrip:
 1_ Put the spacer (15) (if installed), the handgrip (14), the plates (13) and the screws (11) and (12) in position. TORQUE the screws (11) and (12) to 0.8 m.daN (70.79 lbf.in).
 (e) Tighten the screws (1) and (4) and install the cap(s) (3).
 (f) Install the handgrip cover (9). Make sure that the lugs (10) of the handgrip cover engage correctly. Press the handgrip cover into position until you hear a click. 
R  (3) Install the lining 222TW:
 (a) Put the lining 222TW in position and install the screws (1) and (4), the washers (2) and the caps (3). 
R  (4) Install the lining 222VW:
 (a) Put the lining 222VW in position and install the screws (1) and the washers (2). 
R  (5) Install the lining 222UW:
 (a) Put the lining 222UW in position and install the screws (1) and the washers (2).
 (b) Put the latch hook (18) in position and install the screws (16) and the washers (17).
 (c) Install the handgrip:
 1_ Put the spacer (15) (if installed), the handgrip (14), the plates (13) and the screws (11) and (12) in position. TORQUE the screws (11) and (12) to 0.8 m.daN (70.79 lbf.in).
 2_ Install the handgrip cover (9). Make sure that the lugs (10) of the handgrip cover engage correctly. Press the handgrip cover into position until you hear a click. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(24)