(2)
 Remove the cabin escape facilities: FOR 831AZ, 841AZ remove the escape slide/rafts (Ref. TASK 25-62-44-000-002).

 Subtask 25-23-46-865-050
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
 4. Procedure
_________ (Ref. Fig. 401/TASK 25-23-46-991-001) WARNING : MAKE SURE THE PERCUSSION LEVER OF THE DOOR DAMPER CYLINDER IS IN
_______
 THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

 Subtask 25-23-46-020-050
 A. Removal of the Linings
 (1)
 Remove the lining 831FZ (841FZ) (8)

 (a)
 Remove the screws (26) the washers (25) and the grip (27).

 (b)
 Remove the screws (4) and the washers (3).

 (c)
 Loosen the screws (4) and turn the brackets.

 (d)
 Carefully release the lining (8) and remove it.

 (2)
 Remove the lining 831GZ (841GZ) (9)

 (a)
 Disconnect the rod (7) from the lining (9).

 (b)
 Remove and discard the cotter pin (6).

 EFF : ALL

25-23-46Page 402

 (c)
 Remove the pin (5).

 (d)
 Remove the lining (9).

 (3)
 Remove the lining 831EZ (841EZ) (2)

 (a)
 Remove the screws (4) and the washers (3).

 (b)
 Release the lining (2) from the yo-yo rolls and remove it.

 (4)
 Remove the hand grip and the lining 831DZ (841DZ) (21) CAUTION : DO NOT USE TOO MUCH FORCE WHEN YOU REMOVE THE COVER AS THIS

_______
 CAN CAUSE DAMAGE TO THE RETAINER.

 (a)
 Carefully push the lugs (28) of the handgrip cover (22) with your finger in the direction of the arrows and remove the handgrip cover (22).

 (b)
 Remove the screws (17) and (23), the washers (18) and the
 handgrip (24).

 (c)
 Remove the spacer (19) and the lining (20).

 (d)
 Remove the screws (4) and the washers (3).

 (e)
 Release the lining (21) from the yo-yo rolls and remove it.

 (5)
 Remove the handle plate (14) and lining 831CZ (841CZ) (1)

 (a)
 Remove the nut (12), the washer (13), the screw (15) and the handle plate (14) from the emergency control handle (16).

 (b)
 Remove the screws (4) and the washers (3).

 (c)
 Release the lining (1) from the yo-yo rolls and remove it.

 (6)
 Remove the lining 831BZ (841BZ) (10)

 (a)
 Remove the screws (4) and the washers (3).

 (b)
 Release the lining (10) from the yo-yo rolls and remove it.

 EFF : ALL

25-23-46Page 403

R  Door Linings - FWD Passenger/Crew Doors Figure 401/TASK 25-23-46-991-001- 13 (SHEET 1)
 EFF :  ALL  25-23-46 Page 404 May 01/02
 CES 

R  Door Linings - FWD Passenger/Crew Doors Figure 401/TASK 25-23-46-991-001- 23 (SHEET 2)
 EFF :  ALL  25-23-46 Page 405 May 01/02
 CES 

R  Door Linings - FWD Passenger/Crew Doors Figure 401/TASK 25-23-46-991-001- 33 (SHEET 3)
 EFF :  ALL  25-23-46 Page 406 May 01/02
 CES 

 (7) Remove the lining 831AZ (841AZ) (11)
 (a)
 Remove the screws (4) and the washers (3).

 (b)
 Release the lining (11) from the yo-yo rolls and remove it.

 EFF : ALL

25-23-46Page 407

 TASK 25-23-46-400-001
 Installation of the Door Linings at the FWD Passenger/Crew Doors
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)

 B. Referenced Information
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(31)