(2)
 Attach the carpet with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-065) to the partition (1).

 **ON A/C 201-210,
 Subtask 25-26-42-420-054
 B. Installation of the Partition: NOTE : The procedure to install the left and right partitions is the
____
 same.

 NOTE : On aircraft with Claircom phones installed, partitions are marked
____
 with locations.

 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Apply COMMON GREASE (Material No. 04-004) on the lower supports (8) and the stoppers (7) and install them in the seat tracks (9).

 (4)
 Put the MISCELLANEOUS (Material No. 19-002) in position in the seat tracks (9).

 (5)
 Make a loop at one end of the cords.

 (6)
 Apply sealants to the seat tracks (9). WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE

_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
 (a) Apply SEALANTS (Material No. 09-018) in position in the seat tracks (9) on a length of 25.4 mm (1.0000 in.).
 (7)
 Push the loop into the sealant.

 (8)
 Install the partition.

 (a)
 Lower the partition (1) onto the lower supports (8) and the stoppers (7) and support the partitions (1).

 (b)
 Push the release pin (5) in the release hole and move the support tubes (2) up into the upper support (3).

 (c)
 Turn the support tubes (2) 90 degrease clockwise or counterclockwise until they engage.

 (d)
 Make sure that the partition (1) is in a vertical position.

 (e)
 Install the screws (6).

 (9)
 Attach the carpet with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-065) to the partition (1).

 **ON A/C 301-399,
 Subtask 25-26-42-420-054-B
 B. Installation of the Partition. WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR
_______
 INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.

 (Ref. Fig. 401B/TASK 25-26-42-991-005-B)
 (1) Unless specified, TORQUE all nuts, bolts and screws (Ref. TASK 20-21-11-911-001).
 NOTE : The procedure for the left and/or right partition is the same.
____
 EFF : 201-210, 301-399, 25-26-42Page 415

May 01/05
R
 CES  (2) Install the partition (1):

 (a)
 Put the seat track fittings (7) and the stoppers (6) in position as recorded in the removal procedure.

 (b)
 Put the partition (1) with the tubes (3) in position in the panel (2).

 (c)
 Make sure that the partition (1) is in a vertical position.

 (d)
 Install the screws (4) and the washers (5).

 (e) Install the covers (8). R **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399,
 5. Close-up
________ R **ON A/C 001-049, 101-105, 151-199, 201-210,
 Subtask 25-26-42-410-056
 A. Install the curtain from the Center Class Divider (Ref. TASK 25-26-41-400-013).
 (1)
 Make sure that all of the placards of the retained/new components are in the correct position and in a good condition.

 (2)
 If necessary install new placards (Ref. TASK 11-00-00-400-007) and (Ref. AMM 11-32-25 P.Block 001).

 **ON A/C 301-399,
 Subtask 25-26-42-410-056-A
 A. Close Access
 (1)
 Install the curtain from the center class divider (Ref. TASK 25-26-41-400-013).

 (2)
 Close the passenger/information units (PSIU) (Ref. TASK 25-25-11-400-001).

R  EFF : 001-049, 101-105, 151-199, 201-210, 25-26-42Page 416 301-399, May 01/05
 CES

 (3)
 Install the doghouse forward of the partition, if removed (Ref. TASK 25-27-46-400-001).

 (4)
 Make sure that all of the placards of the retained/new components are in the correct position and in a good condition.

 (5)
 If necessary install new placards (Ref. TASK 11-00-00-400-007) and (Ref. AMM 11-32-25 P.Block 001).

R  **ON A/C 001-049, 101-105, 151-199, 201-210, 301-399,
 Subtask 25-26-42-862-051
 B. De-energize the ground service network
 (Ref. TASK 24-42-00-862-001).

R  EFF : 001-049, 101-105, 151-199, 201-210, 25-26-42Page 417 301-399, May 01/05
 CES

 DIVIDER - CLASS - REMOVAL/INSTALLATION
______________________________________
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(75)