(b)
 Apply the STORAGE PRESERVATION (Material No. 15-004) into the seat tracks (10).

 (c)
 Apply the STORAGE PRESERVATION (Material No. 15-008) into the seat tracks (10).

 (d)
 Apply the COMMON GREASE (Material No. 04-022) into the seat tracks (10).

 (e)
 Cut the section (9) to the required lenght and push it into the grease (11). Do this only in areas where persons walk and not in areas where furnishings will be installed.

 (f)
 Remove the unwanted grease (11) with a SCRAPER - NON METALLIC. Do this at the top of the seat track (10) to get a flush surface.

 NOTE : Make sure that the complete seat track (10) is filled with
____ COMMON GREASE (Material No. 04-022) (11) where the adhesive foil (4) will be installed above the seat track (10).
 (g) Remove the masking paper and masking tape from the floor panels.
 (3) Preparation of the Floor Panel (6):
 (a)
 Make sure that the component is free from dust and particles. If necessary use a vacuum cleaner.

 (b)
 Clean the component interface and/or the adjacent area.
 Use CLEANING AGENTS (Material No. 11-004).

 (c)
 Do an inspection of the component interface and/or the adjacent area.

R  EFF : 106-149, 157-199, 210-299, 301-399, 25-28-42Page 438 401-499, Aug 01/05
 CES

 (4) Installation of the self-adhesive foil (4) to the floor panel (6):
 NOTE : It is recommended that two persons do this procedure.
____
 (a)
 Unwind 100 mm (4.0 in.) of the self-adhesive foil BONDING AND ADHESIVE COMPOUNDS (Material No. 08-104) (4) from the roll and remove the protective paper.

 (b)
 Install the adhesive foil (4) with a soft cotton cloth and with a light pressure of your hand make it smooth onto the floor panel (6). Work from the middle of the adhesive foil (4) towards the sides.

 (c)
 With a ROLLER - RUBBER press the adhesive foil (4) onto the floor panel (6).

 NOTE : Move the ROLLER - RUBBER forwards and backwards and around
____
 the edges for a better bond.

 (d) For the installation of one more piece of adhesive foil (4) do the steps (4)(a) thru (c).
 NOTE : You must make sure that the adhesive foil (4) has an
____ overlap of 50 mm (2.0 in.) on adhesive foil (4) which you have already installed.
 Subtask 25-28-42-420-055-A
 E. Installation of the NTF Assy to the Floor Panel (Ref. Fig. 401A/TASK 25-28-42-991-001-A, 402A/TASK 25-28-42-991-006-A)
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1) Make sure that the component is free from dust and particles. If necessary use a vacuum cleaner.
R  EFF : 106-149, 157-199, 210-299, 301-399, 25-28-42Page 439 401-499, Aug 01/05
 CES  (2) Installation of the NTF Assy:

 (a)
 Clean the component interface and/or the adjacent area.
 Use CLEANING AGENTS (Material No. 11-004).

 (b)
 Do an inspection of the component interface and/or the adjacent area.

 NOTE : It is recommended that two persons do this procedure
____
 (c) Carefully put the NTF assy (1) in position and align it with the floor panels (6).
 NOTE : Make sure that you leave a gap of 5.0 +2.0 -2.0 mm (0.1968
____ +0.0787 -0.0787 in.) between the NTF assy (1) and the interior equipment (toilet, galley etc.).
 NOTE : Make sure that you leave a gap of 3.0 +1.0 -0.5 mm (0.1181
____ +0.0393 -0.0196 in.) between the NTF-covering sheets.
 (d) Remove 100 mm (4 in.) of the protective paper from the NTF assy (1).
 NOTE : We recommend that you do this on a corner of the NTF assy
____
 (1).

 (e)
 Install the NTF-covering to the adhesive-foil (4) with a soft cotton cloth MISCELLANEOUS (Material No. 19-003) and a light pressure of you hand. Make sure that the NTF-covering is in the correct position.

 (f)
 Install the NTF assy (1) with a ROLLER - RUBBER. Work from the middle of the NTF assy (1) to the sides, backwards and forwards and around the edges for a better bond.

 (g)
 Do the steps (3) (c) thru (f) until you have installed all of the NTF assy (1) to the floor panel (6).

 (h)
 If the floor path marking was removed, put it in position
 (Ref. TASK 33-51-12-400-001).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(114)