EFF : ALL
25-28-42Page 463
R Subtask 25-28-42-420-057
R E. Installation of the NTF Assy to the Floor Panel (Welding Procedure) R (Ref. Fig. 403/TASK 25-28-42-991-011, 404/TASK 25-28-42-991-012)
R WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ R AREA WHEN YOU USE SPECIAL MATERIALS. R IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH R OR IN YOUR EYES : R -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 R MINUTES. R -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. R DO NOT BREATHE THE FUMES FROM THE MATERIAL. R DO NOT SMOKE WHEN YOU USE THE MATERIAL. R DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF R HEAT. R THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE R AND SKIN IRRITANTS.
R (1) Make sure that the installation area is free from dust and particles. R If necessary use a vacuum cleaner.
R (2) Installation of the NTF Assy:
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ R THIS/THESE MATERIAL/S. R USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R (a) Clean the component interface and/or the adjacent area. R Use CLEANING AGENTS (Material No. 11-004).
R (b) Do an inspection of the component interface and/or the adjacent R area.
R NOTE : It is recommended that two persons do this procedure.
____
R (c) Carefully put the NTF assy (10) in position.
R (d) Make the cut outs for the furnishing location points as R necessary.
R NOTE : You must leave a gap of 5.0 +2.0 -2.0 mm (0.1968 +0.0787 -
____ R 0.0787 in.) between the NTF assy (10) and the interior R equipment (toilet, galley etc.).
R NOTE : You must leave a gap of 1.5 +1.0 -1.0 mm (0.0590 +0.0393 -
____ R 0.0393 in.) between the NTF-covering sheets.
EFF : ALL
25-28-42Page 464
May 01/04
R (e) Remove the protective paper from the NTF assy (10) and install it
R to the Moisture Barrier Foil (MYLAR) (4) / Floor Panels (6).
R (f) Install the NTF-covering on the Moisture Barrier Foil (MYLAR) (4)
R with a soft cotton cloth MISCELLANEOUS (Material No. 19-003) and
R a light pressure of your hand. Work from the middle of the NTF
R and press towards the edges to prevent wrinkles or air pockets.
R (g) Install the NTF assy (10) with a ROLLER - RUBBER. Work from the
R middle of the NTF assy (10) to the sides, backwards and forwards
R and around the edges for a better bond.
R (h) Do the steps (3) (c) thru (g) until you have installed all of the
R NTF assy (10) to the floor panel (6).
R (3) Preparation of Welding area:
R (Ref. Fig. 405/TASK 25-28-42-991-013)
R (a) Chamfer the edges of the NTF-covering at the joints with a
R TRIANGLE. Make a groove in the shape of a "V" with an angle of
R approximately 30 on the NTF edges. A stainless steel or
R aluminiuim flexible ruler will help to make a straight groove.
R CAUTION : DO NOT CAUSE DAMAGE TO THE MOISTURE BARRIER FOIL_______
R (MYLAR).
R NOTE : The depth of the groove must not be deeper than 2/3 of the____
R floor covering tickness.
R (b) Remove loose particles out from the groove. Use a vacuum cleaner
R if necessary.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備2(121)
