(1)
Lift up the cover (30), remove the screw (12), the nut (13) and the plate (31).
(2)
Remove the screws (10) and the washers (11).
(3)
Remove the plugs (32) and the screws (33) and the door lining (2).
(4)
Remove the cabin pressure warning light panel (Ref. TASK 52-73-22-000-003)
(5)
Remove the slide armed indicater light (Ref. TASK 52-73-21-000-003) remove the door lining (2).
Subtask 25-23-47-020-111
D. Removal of the Door Lining 833DZ (6)
(Ref. Fig. 402/TASK 25-23-47-991-014)
CAUTION : DO NOT USE TOO MUCH FORCE WHEN YOU REMOVE THE COVER AS THIS CAN
_______
CAUSE DAMAGE TO THE RETAINER.
(1)
Carefully push the lugs (29) of the cover (26) with your finger in the direction of the arrows and remove the cover (26).
(2)
Remove the screw (22), the washer (23) and the cover (21).
(3)
Remove the screws (28) and the washers (27) and the LWR handle section (25).
(4)
Pull the door lining (6) up to release the engage brackets from the yo-yo rolls and remove the door lining (6).
Subtask 25-23-47-020-112
E. Removal of the Door Lining 833GZ (3)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1) Remove the screws (12), (16), (20), the washers (15), (19) the nut (13), the bracket (24) and the door lining (3) in the sequence as shown.
Door Linings, zone 231.
Figure 402/TASK 25-23-47-991-014- 12 (SHEET 1)
CES
Door Linings, zone 231.
Figure 402/TASK 25-23-47-991-014- 22 (SHEET 2)
CES
(2) Identify the position of the screws, the washers, the nut and the bracket for the installation procedure.
Subtask 25-23-47-020-113
F. Removal of the Door Lining 833HZ (4)
(Ref. Fig. 402/TASK 25-23-47-991-014)
(1)
Remove the screws (10) and the washers (11).
(2)
Remove the screws (14) and pull the door lining (4) down to release the engage brackets from the yo-yo rolls and remove the door lining (4).
TASK 25-23-47-400-012
Installation of the Door Linings of the LH FWD Emergency Exit Door, zone 231
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
11-00-00-400-002 Installation of the Decals
24-42-00-861-001 Energize the Ground Service Network from the External Power
24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power
52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment
52-22-00-410-001 Closing of the Emergency Exit Doors from the Passenger Compartment
52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder
52-73-21-400-003 Installation of the SLIDE ARMED Indicator-Light (2WN1, 2WN2, 21WN1, 21WN2) of the Emergency Exit
52-73-22-400-003 Installation of the CABIN PRESSURE Warning Light Panel of the Emergency Exit Door (19WN1,19WN2,20WN1,20WN2)
AMM 11-32-25 P.Block 001 INTERIOR PLACARDS (SEE ALSO 11-42-25)
25-23-47-991-014 Fig. 402
3. Job Set-up__________
Subtask 25-23-47-860-068
A. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is in position on the related emergency exit door.
(2)
Make sure that the related emergency exit door is open (Ref. TASK 52-22-00-010-001)
(3)
Make sure that the door is safe (Ref. TASK 52-22-00-860-003)
(4)
Make sure that the ground service network is energized
(Ref. TASK 24-42-00-861-001)
(5)
Clean the component interface and/or the adjacent area.
(6)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(7) Do an inspection of the component interface and/or the adjacent area. Subtask 25-23-47-865-082
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM EQUIPMENT/FURNISHINGS 設(shè)備2(45)
