(b)
Connect the end of the BTMS sensor subassembly (5) to the
retainer (6) as follows:
-install the BTMS retainer clip (10) in the holes of the retainer (6).
-bend the ends of the retainer clip (10).
(c)
Install the screw (3) and the washer (4) . TORQUE the screw (3) to 0.57 m.daN (50.44 lbf.in).
(d)
Make sure that the heat shrink sleeve (9) is in the correct condition and connect the electrical connector (2) to the sensor receptacle (1).
(e)
Fold back the end of the sleeve (9) on the connector (2) to cover it fully.
1EFF : 301-399, 1 32-47-15Page 410 1 1 May 01/05R 1 1 1CES 1
R R R R R R R R R R R R R (f) If the heat shrink sleeve (9) is not in the correct condition, install a new sleeve as follows: - cut a piece of heat shrink sleeve (9) to a length between 52 mm (2.0472 in.) and 58 mm (2.2834 in.). - install the heat shrink sleeve (9) on the electrical connector (2). - connect the electrical connector (2) to the receptacle (1). - move the heat shrink sleeve (9) onto the connector but do not put the sleeve on the milled external part of the connector. - increase the temperature of the heat shrink sleeve to a minimum of 135 deg.C (275.00 deg.F) until you get full shrinking at the backshell only, so that you can disconnect the plug without destruction at the sleeve.
R **ON A/C ALL
Subtask 32-47-15-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GW
Subtask 32-47-15-710-050
C. Test
(1) Do the operational test of the brake temperature system. (Ref. TASK 32-47-00-710-001)
5. Close-up________
Subtask 32-47-15-942-050
A. Removal Equipment
(1) Remove the warning notice(s).
(2) Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 32-47-15Page 411 1 1 Feb 01/05 1 1 1CES 1 MONITORING UNIT - BRAKE TEMPERATURE (2GW,3GW,8GW,9GW) - REMOVAL/INSTALLATION
____________________________________________________________________________
TASK 32-47-18-000-001
Removal of the Brake Temperature Monitoring Unit
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing Gears
R **ON A/C 001-003, 051-052,
32-47-18-991-001-B Fig. 401
1EFF : ALL 1 32-47-18Page 401 1 1 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
32-47-18-991-001-C Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
Subtask 32-47-18-941-050
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(30)
