A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
Subtask 32-47-18-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/BRK/TEMP/DET/UNIT 1GW M37
4. Procedure
_________
**ON A/C 001-003, 051-052,
(Ref. Fig. 401/TASK 32-47-18-991-001-B)
1EFF : ALL 1 32-47-18Page 402 1 1 Aug 01/05 1 1 1CES 1
Brake Temperature Monitoring Unit - Location and Detail Figure 401/TASK 32-47-18-991-001-B
R 1EFF : 001-003, 051-052, 1 32-47-18Page 403 1 1 May 01/05 1 1 1CES 1R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 32-47-18-991-001-C)
**ON A/C 001-003, 051-052,
Subtask 32-47-18-020-050-B
A. Removal of the Brake Temperature Monitoring Unit
(1)
Move the rubber shields (4) sufficiently to get access to the electrical connectors (6).
(2)
Disconnect the electrical connectors (6) from the brake temperature sensors (5).
(3)
Move the rubber shield (10) sufficiently to get access to the electrical connector (9).
(4)
Disconnect the electrical connector (9) from the brake temperature monitoring unit (11).
(5)
Put blanking caps on the disconnected electrical connectors.
(6)
Put blanking caps on the brake temperature sensor (5) connector receptacles.
(7)
Put a blanking cap on the monitoring unit (11) connector receptacle.
(8)
Remove the nuts (8), the washers (7) and the bolts (1). Remove the monitoring unit (11) from the bracket (2).
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 32-47-18-020-050-C
A. Removal of the Brake Temperature Monitoring Unit
(1)
Move the rubber shields (3) sufficiently to get access to the electrical connectors (5).
(2)
Disconnect the electrical connectors (5) from the brake temperature sensors (4).
1EFF : ALL 1 32-47-18Page 404 1 1 Aug 01/05 1 1 1CES 1
Brake Temperature Monitoring Unit - Location and Detail Figure 401A/TASK 32-47-18-991-001-C
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-47-18Page 405 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(3)
Move the rubber shield (9) sufficiently to get access to the electrical connector (8).
(4)
Disconnect the electrical connector (8) from the brake temperature monitoring unit (10).
(5)
Put blanking caps on the disconnected electrical connectors.
(6)
Put blanking caps on the brake temperature sensor (4) connector receptacles.
(7)
Put a blanking cap on the monitoring unit (10) connector receptacle.
(8)
Remove the nuts (7), the washers (6) and the bolts (1). Remove the monitoring unit (10) from the bracket (2).
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-47-18Page 406 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL
TASK 32-47-18-400-001
Installation of the Brake Temperature Monitoring Unit
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
No specific Milliohmmeter Megger, Type BT51
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(31)
