-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-11-00-586-001 Lowering of the Aircraft at Forward Jacking Point,
 MLG Wheels on the Ground 07-12-00-582-001 Jacking for Nose Gear Wheel Change 09-10-00-584-002 Towing with the Nose Gear from the Front 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the
 External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 29-10-00-863-001 Pressurize the Green Hydraulic System R 29-10-00-863-002 Pressurize the Yellow Hydraulic System 29-10-00-864-001 Depressurize the Green Hydraulic System
R  29-10-00-864-002 Depressurize the Yellow Hydraulic System 31-60-00-860-001 EIS Start Procedure 31-60-00-860-002 EIS Stop Procedure 32-51-00-720-003 Functional Test of the Nose Wheel Steering with the
 Handwheel.
 3. Job Set-up
__________
R  **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 Subtask 32-51-00-860-073
 A. Aircraft Maintenance Configuration
 (1)
 Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).

 (2)
 Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001).

 (3)
 If the test is to be done with the nosewheels on the ground, do these steps:

 NOTE : You will need two 1.2 m (3.93 ft.) square steel plates.
____
 (a)
 Position a steel plate in front of the nosewheels.

 (b)
 Apply a thick layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) to the upper surface of the steel plate.

 1EFF : ALL 1 32-51-00Page 540 1 1 Aug 01/05 1 1 1CES 1 NOTE : Do not mix Material No. 04-004 with Material No. 04-022.

____ You can use Material No. 04-022 as an alternative to Material No. 04-004. Clean and degrease the parts before you use Material No. 04-022.
 (c)
 Put the other steel plate on the top of the greased steel plate.

 (d)
 Move the aircraft and position the nosewheels on the greased steel plates (Ref. TASK 09-10-00-584-002).

 (4) If the test is to be done with the nose wheels clear of the ground do this:
 (a) Lift the nose gear (Ref. TASK 07-12-00-582-001). NOTE : Use only a compact axle jack to lift the nose gear.
____
 (5)
 On the nose gear leg, on the electrical box, make sure that the
 towing lever is in the normal position (engaged position).

 (6)
 On the panel 400VU, make sure that the landing gear control lever is in the DOWN position.

 (7)
 On the panel 402VU, make sure that the ANTI SKID NOSE WHEEL switch is in the ON position.

 (8)
 Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only)
 (Ref. TASK 31-60-00-860-001).

 (9)
 On the ECAM control panel, push the WHEEL pushbutton switch.

 (10)
 Make sure that the rudder pedals and the two nose-wheel steering handwheels are in the neutral position.

 (11)
 On the overhead panel 23VU:

 -Make sure that the FLT CTL/ELAC 1 pushbutton switch is pushed (on this pushbutton switch, the OFF and FAULT legends are OFF).

 (12)
 On the overhead panel 24VU:

 -Make sure that the FLT CTL/ELAC 2 pushbutton switch is pushed (on this pushbutton switch, the OFF and FAULT legends are OFF).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-51-00Page 541 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

R  **ON A/C 401-499, 
R  Subtask 32-51-00-860-073-A 
R  A. Aircraft Maintenance Configuration 
R  (1) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-
R  002). 
R  (2) Pressurize the Yellow hydraulic system (Ref. TASK 29-10-00-863-002). 
R  (3) If the test is to be done with the nosewheels on the ground, do these 
R  steps: 
R  NOTE : You will need two 1.2 m (3.93 ft.) square steel plates.____ 
R  (a) Position a steel plate in front of the nosewheels. 
R  (b) Apply a thick layer of COMMON GREASE (Material No. 04-004) or 
R  COMMON GREASE (Material No. 04-022) to the upper surface of the 
R  steel plate. 
R  NOTE : Do not mix Material No. 04-004 with Material No. 04-022.____ 
R  You can use Material No. 04-022 as an alternative to 
R  Material No. 04-004. Clean and degrease the parts before 
R  you use Material No. 04-022. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(88)