TASK 32-49-16-000-002 Removal of the MLG Tire-Pressure Transducer Adaptor WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change 32-49-16-991-002 Fig. 402
3. Job Set-up
__________ Subtask 32-49-16-941-057
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
In the cockpit, on the panel 400VU put the warning notice(s) to tell persons not to operate the landing gear control lever.
(3)
Make sure that the wheel chocks are in position.
1EFF : 051-099, 1 32-49-16Page 410 1 1 May 01/05 1 1 1CES 1 Subtask 32-49-16-865-054
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/TIRE/PRESS 1GV M31
Subtask 32-49-16-860-063
C. Aircraft Maintenance Configuration
(1)
Lift the related axle with jack (Ref. TASK 07-12-00-582-002).
(2)
Fully deflate the tire.
4. Procedure
_________
(Ref. Fig. 402/TASK 32-49-16-991-002) Subtask 32-49-16-020-051
A. Removal of the Pressure Transducer Adaptor
(1)
Remove the cotter pin (6) and discard it. Remove the nut (7).
(2)
Remove the pressure transducer (5).
(3)
Remove the pressure transducer adaptor (3).
1EFF : 051-099, 1 32-49-16Page 411 1 1 May 01/05 1 1 1CES 1
MLG Tire-Pressure Transducer Adaptor
Figure 402/TASK 32-49-16-991-002
1EFF : 051-099, 1 32-49-16 Page 412
1 1 May 01/05
1 1
1CES 1
TASK 32-49-16-400-002
Installation of the MLG Tire-Pressure Transducer Adaptor
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
2 packing 32-49-16 01 -040 4 packing 32-49-16 01 -050 6 cotter pin 32-49-16 01 -010
1EFF : 051-099, 1 32-49-16Page 413 1 1 May 01/05 1 1 1CES 1
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change 12-14-32-614-001 Nitrogen Filling of the Tires 32-49-00-720-001 Crosscheck TPIS Reading and Tire Pressure Gauge 32-49-16-991-002 Fig. 402
3. Job Set-up
__________ Subtask 32-49-16-860-064
A. Aircraft Maintenance Configuration
(1)
Make sure that the safety barriers are in position.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架8(61)
