(5)
 Install the facing washer (8) and the insulation washer (9) on the bolt (14).

 (6)
 Install the bolt (14), the insulation washer (13), the facing washer

 (11) and the nut (12).

 (7)
 Put the bleed-air duct (5) in position.

 (8)
 Install the clamps (4) and (6) and TORQUE to between 0.56 and 0.79 m.daN (49.55 and 69.91 lbf.in).

 (9)
 Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to these items:

 -clamps (3), (4) and (6)
 -washers (8), (9), (11) and (13), nut (12) and bolt (14).

 Subtask 36-11-48-790-054
 G. Leak Test
 (1) Do a leak test of the applicable bleed-air ducts (Ref. TASK 36-11-00-720-004) and (Ref. TASK 36-11-00-720-005).
 Subtask 36-11-48-930-051
 H. Mark the Clamps
 (1) Use marking paint F404-717 to make a mark 2.0 mm (0.0787 in.) wide and 8.0 mm (0.3149 in.) long on the applicable clamps as follows:
 -
clamps (3), (4) and (6)
 (Ref. Fig. 401/TASK 36-11-48-991-010)

 -
clamps (75) and (79)

 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
 (Ref. Fig. 403/TASK 36-11-48-991-012)

R **ON A/C 106-149, 211-299, 301-399, 401-499,
 (Ref. Fig. 403A/TASK 36-11-48-991-012-A)
 **ON A/C ALL
 -
clamps (111), (121) and (123) (LH wing)
 (Ref. Fig. 404/TASK 36-11-48-991-013)

 -
clamps (111), (121) and (123) (RH wing)
 (Ref. Fig. 405/TASK 36-11-48-991-014)

 -clamp (158).
 (Ref. Fig. 406/TASK 36-11-48-991-015)

 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
 Subtask 36-11-48-420-095-A
 J. Installation of the Insulation Muffs
 (1) Install and safety with MISCELLANEOUS (Material No. 19-001) the applicable insulation muffs, as follows:
 -
insulation muffs (2) and (7) (Ref. Fig. 401/TASK 36-11-48-991-010)

 -
insulation muffs (29), (46) and (64) (Ref. Fig. 402/TASK 36-11-48-991-011-A)

 -
insulation muffs (78) and (90) (Ref. Fig. 403/TASK 36-11-48-991-012)

 -
insulation muffs (112) and (122) (LH wing) (Ref. Fig. 404/TASK 36-11-48-991-013)

 -
insulation muffs (112) and (122) (RH wing) (Ref. Fig. 405/TASK 36-11-48-991-014)

 -
insulation muff (161). (Ref. Fig. 406/TASK 36-11-48-991-015)

R **ON A/C 106-149, 211-299, 301-399, 401-499,
 Subtask 36-11-48-420-095
 J. Installation of the Insulation Muffs
 (1) Install and safety with MISCELLANEOUS (Material No. 19-001) the applicable insulation muffs, as follows:
 -
insulation muffs (2) and (7) (Ref. Fig. 401/TASK 36-11-48-991-010)

 -
insulation muffs (24), (45) and (61) (Ref. Fig. 402A/TASK 36-11-48-991-011)

 -
insulation muffs (78) and (90) (Ref. Fig. 403A/TASK 36-11-48-991-012-A)

 -
insulation muffs (112) and (122) (LH wing) (Ref. Fig. 404/TASK 36-11-48-991-013)

 -
insulation muffs (112) and (122) (RH wing) (Ref. Fig. 405/TASK 36-11-48-991-014)

 -
insulation muff (159). (Ref. Fig. 406/TASK 36-11-48-991-015)

 **ON A/C ALL
 5. Close-up
________ Subtask 36-11-48-410-057
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the access panels (Ref. TASK 57-41-37-400-002), (Ref. TASK 57-41-37-400-005):

 (a)
 For the left wing: 521AB, 521BB, 521CB, 521DB, 521EB, 521FB, 521BT.

 (b)
 For the right wing: 621AB, 621BB, 621CB, 621DB, 621EB, 621FB, 621BT.

 Subtask 36-11-48-865-065
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV, 2KS2, 2KS1, 2HA1, 4KS2, 4KS1, 2HA2.
 Subtask 36-11-48-860-055
 C. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1) Retract the slats (Ref. TASK 27-80-00-866-005). Subtask 36-11-48-942-053
 D. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 1EFF : ALL 1 36-11-48Page 441 1 1 Feb 01/05R 1 1 1CES 1

 (4) Remove the ground support and maintenance equipment, the special and

 standard tools and all other items.