C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R R R R R R 15 15 15 15 15 15 E-seals E-seals E-seals E-seals E-seals E-seals 36-11-41 02 -025 36-11-41 02 -025A 36-11-51 02 -025 36-11-51 02 -025A 36-11-52 02 -040 36-11-52 02 -040A
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 24-42-00-862-001 71-13-00-010-040 71-13-00-410-040 78-30-00-081-041 78-30-00-481-041 78-36-00-010-040 78-36-00-410-040 36-11-49-991-301 Energize the Aircraft Electrical Circuits from the External PowerDe-energize the Ground Service Network Supplied from the External PowerOpening of the Fan Cowl DoorsClosing of the Fan Cowl DoorsMake the Thrust Reverser Serviceable after MaintenanceMake the Thrust Reverser Unserviceable for MaintenanceOpening of the Thrust Reverser DoorsClosing of the Thrust Reverser DoorsFig. 402
3. Job Set-up__________
Subtask 36-11-49-860-060
A. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized (Ref. TASK 24-41-00-861-002).
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the AIR COND panel 30VU:
-Make sure that the ENG 1(2) BLEED pushbutton switch is released
(the OFF legend is on), R - Make sure that the APU BLEED pushbutton switch is released (the ON R legend is off),
-Make sure that the warning notice to tell persons not to operate the pneumatic system is in position.
(4)
On the ENG panel 115VU:
-Make sure that the warning notice to tell persons not to start the engine 1(2) is in position.
(5)
On the HP ground connector:
-Make sure that the warning notice to tell persons not to pressurize the pneumatic system is in position.
(6)
On the ENG section of the maintenance panel 50VU:
-
Make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off,
-
Make sure that the warning notice to tell persons not to energize the FADEC 1(2) is in position.
(7)
Make sure that the access platform is in position below the engine.
Subtask 36-11-49-010-075
B. Get Access
(1)
Make sure that the fan cowl doors are open (Ref. TASK 71-13-00-010-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2)
Make sure that the thrust reverser doors are open (Ref. TASK 78-36-00-010-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 36-11-49-040-058
C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
Subtask 36-11-49-865-054
D. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/ENG 1/CTL 3HA1 D12 49VU AIR BLEED/ENG 1/MONG 2HA1 D11 122VU AIR BLEED/ENG 2/CTL 3HA2 Z23 122VU AIR BLEED/ENG 2/MONG 2HA2 Z22
4. Procedure
_________
(Ref. Fig. 402/TASK 36-11-49-991-301)
Subtask 36-11-49-420-051
A. Installation of the Mid Stage Tee Duct
(1)
Remove the blanking plugs from the mid stage tee duct (20), the bleed pressure regulator valve (5), the High Pressure (HP) bleed valve (40), and the Intermediate Pressure (IP) bleed check valve (45).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 1(122)
