-
make sure that the APU BLEED pushbutton switch is released (the ON legend is off)
-put a warning notice to tell persons not to operate the pneumatic system.
(5)
On the HP ground connector:
-put a warning notice to tell persons not to pressurize the pneumatic system.
Subtask 36-11-00-865-063
D. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/ENG 1/CTL 3HA1 D12 49VU AIR BLEED/ENG 1/MONG 2HA1 D11 122VU AIR BLEED/ENG 2/CTL 3HA2 Z23 122VU AIR BLEED/ENG 2/MONG 2HA2 Z22
1EFF : ALL 1 36-11-00Page 403 1 1 Aug 01/03R 1 1 1CES 1
Subtask 36-11-00-010-050
E. Get Access
(1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2)
Put the access platform in position below the engine.
Subtask 36-11-00-040-050
F.
Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041). Subtask 36-11-00-010-071
G. Open the left thrust-reverser cowl door (Ref. TASK 78-36-00-010-040): FOR 1000EM1 451AL FOR 1000EM2 461AL
4. Procedure
_________
**ON A/C 001-003, 051-054, 056-056,
(Ref. Fig. 401/TASK 36-11-00-991-001) R **ON A/C 004-049, 055-055, 057-099, 101-149, 151-199, 201-299, 301-399, R 401-499, (Ref. Fig. 401A/TASK 36-11-00-991-001-A) **ON A/C ALL
(Ref. Fig. 402/TASK 36-11-00-991-033)
Bleed-Pressure Regulator Valve
Figure 401/TASK 36-11-00-991-001
R 1EFF : 001-003, 051-054, 056-056, 1 36-11-00Page 405 1 1 May 01/05 1 1 1CES 1
Bleed-Pressure Regulator valve
Figure 401A/TASK 36-11-00-991-001-A
R 1EFF : 004-049, 055-055, 057-099, 101-149, 1 36-11-00Page 406 1151-199, 201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
BLEED page of the ECAM Display Unit Figure 402/TASK 36-11-00-991-033
1EFF : 1 1R 1CES ALL 1 11 1 36-11-00 Page 407 Aug 01/03
Subtask 36-11-00-040-056
A. Deactivation of the Bleed Pressure Regulator Valve CAUTION : CAREFULLY ALIGN THE LOCKING PIN WITH THE DEACTIVATING HOUSING
_______ ON THE VALVE. IF YOU ALIGN IT INCORRECTLY OR IF YOU TIGHTEN IT TOO MUCH, THE LOCKING PIN CAN REMAIN IN POSITION AND YOU CAN CAUSE DAMAGE TO THE LOCKING PIN THREAD.
(1) On the bleed pressure regulator valve (4001HA):
(a)
Use a hexagonal wrench. to set the manual override control to the CLOSED position
(b)
Remove and discard the lockwire from the locking pin (1).
(c)
Lock the override control (the pressure of the valve is released when you remove the locking pin from its storage port).
1 TORQUE the locking pin (1) to between 0.8 and 0.9 m.daN (70.79
_ and 79.64 lbf.in) if the locking pin head is hexagonal.
2 Manually tighten the locking pin (1) if the locking pin is a
_
knurled knob.
(2) On the ECAM control panel, push the BLEED key (on the lower ECAM DU, the BLEED page comes into view).
(a) On the lower ECAM DU, on the BLEED page: R - the related bleed pressure regulator valve is shown fully R closed. R
5. Close-up
________
Subtask 36-11-00-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the left thrust-reverser cowl door (Ref. TASK 78-36-00-410-040): FOR 1000EM1 451AL FOR 1000EM2
461AL Subtask 36-11-00-440-050
B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041). Subtask 36-11-00-410-070
C. Close Access
(1)
Close the fan cowl doors (Ref. TASK 71-13-00-410-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2)
Remove the access platform(s).
(3) Remove the warning notice(s). Subtask 36-11-00-942-053
D. Put a warning notice in the cockpit to tell the crew that the left (right) bleed pressure regulator valve is closed and deactivated.
Subtask 36-11-00-865-064
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2HA1, 2HA2, 3HA1, 3HA2
Subtask 36-11-00-860-072
F. Do the EIS stop procedure
(Ref. TASK 31-60-00-860-002).
Subtask 36-11-00-869-112
G. Make an entry in the log book. Subtask 36-11-00-862-065
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 1(36)
