C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
cotter pin 71-13-13 01A-010
F 『 EEFF : ALL E Page 40471-13-13
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
71-13-00-800-041 Adjustment of the Fan Cowl Doors
71-13-13-991-300 Fig. 401
3. Job Set-up
__________
Subtask 71-13-13-860-051
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
Subtask 71-13-13-010-055
B. Make sure that the fan cowl doors are open (Ref. TASK 71-13-00-010-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
4. Procedure
_________
Subtask 71-13-13-140-050
A. Make sure that the surface where the bolt (5) is to be installed is clean.
Subtask 71-13-13-640-050
R B. Clean the threads of the bolt (5) and apply Silicone Lubricant (Material R No. CP5063) to the threads.
F 『 EEFF : ALL E Page 40571-13-13
E E Nov 01/01 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
Subtask 71-13-13-420-050
C. Installation of the Fan Cowl Door Latches
(1) Install the latch (40) on the left fan cowl door. Attach the latch
(40) to the latch housing (15) with the bolt (5), the bushings (10), (35), the washer (30) and the nut (25).
(2) TORQUE the nut (25) to between 60 and 84 lbf.in (0.67 and 0.94 m.daN) R and install a new cotter pin (20).
(3) Put the housing unit (60) in position on the keeper housing (45) on the right fan cowl door. Attach the housing unit (60) to the keeper housing (45) with the screws (70), the washers (55) and the nuts (50).
(4) TORQUE the nuts (30) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).
(5) Install the clevis (65) in the housing unit (60).
5. Close-up
________
(Ref. Fig. 401/TASK 71-13-13-991-300)
Subtask 71-13-13-410-050
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the fan cowl doors (Ref. TASK 71-13-00-410-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
Subtask 71-13-13-820-050
B. Do the adjustment of the fan cowl doors (Ref. TASK 71-13-00-800-041).
Subtask 71-13-13-942-050
C. Remove the warning notice(s).
F 『 EEFF : ALL E Page 40671-13-13
E E Nov 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
LATCH - FAN COWL DOOR - INSPECTION/CHECK
________________________________________
TASK 71-13-13-220-040
R General Visual Inspection of Fan Cowl Door Hinge Fittings
1. Reason for the Job
__________________
R Refer to the MPD TASK: 711300-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 1(116)
