_
 2 On the upper ECAM display unit:

_ - A message and the applicable procedure come into view. a On the ENG panel 115VU:
_
 - The applicable FIRE legend comes on. 3 A fire Indication by the fire detection loops can be
_ extinguished by portable or onboard fire extinguishing systems.
 4 When there is an external engine fire, do this procedure:
_ a Put the throttle control levers of the engines 1 and 2 in
_ the idle stop position (zero on the graduated sector).
 b On the ENG panel 115VU:
_
 - Set the ENG/MASTER 1(2) switch to OFF. c On the overhead FIRE panel 1WD, push the ENG 1(2) FIRE
_
 pushbutton switch:

 NOTE : After operation of the ENG1(2) FIRE pushbutton
____ switch, do the operational test of the hydraulic fire shut-off valves (Ref. TASK 29-10-00-710-001).
 - The SQUIB legends of the applicable AGENT 1 and AGENT 2 pushbutton switches come on.

 - The audio warning stops.

 F 『 EEFF : ALL E Page A55571-00-00
 E E Aug 01/05 ERE
ECES Ed On the overhead FIRE panel 1WD, push the AGENT 1 and 2

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E 
R 
R 
R 
R 
R

_ pushbutton switches:
- After not many seconds, the DISCH legends of the
pushbutton switches comes on.

e On the ENG panel 115VU:
_
 - Set the ENG/MASTER 2(1) switch to OFF. f Open the cowl doors and extinguish the fire with a fire
_ extinguisher if this procedure does not completely stop the fire.
 g Replace the nacelle fire extinguisher bottles if they are
_ used.
 h Do the procedure (Ref. TASK 72-00-00-200-007).
_
 F 『 EEFF : ALL E Page A55671-00-00
 E E Aug 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E E E TASK 71-00-00-790-001

 Leak Test of the Accessory-Gearbox (AGB) Carbon Seal
 1. Reason for the Job
__________________
 To make sure that there is no leakage from the AGB carbon seals.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific slide hammer No specific suitable container No specific warning notice No specific Torque Wrench : range 36.00 to 220.00 lbf.in
 (0.40 to 2.60 m.daN) No specific Torque Wrench : range 96.00 to 900.00 lbf.in
 (1.00 to 10.00 m.daN) No specific Torque Wrench : range 180.00 to 1800.00 lbf.in
 (2.00 to 20.00 m.daN) 856A1115 1 CART, NITROGEN - FUEL MANIFOLD PRESSURE CHECK 856A2632 1 PULLER 856A2707 1 TOOL SET, LEAK TEST - AGB 856A2718 1 TOOL SET, R/I - DRIVE SHAFTS
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2101 USA MIL-T-5544 graphite grease (Ref. 70-30-00) Material No. CP2442 * engine oil (Ref. 70-30-00)
 F 『 EEFF : ALL E Page A55771-00-00

 E E Aug 01/05 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
20  O-ring 
30  O-rings 
30  O-rings 
30  O-rings 
30  O-rings 

D. Referenced Information

72-63-00 04 -06072-63-00 01B-05072-63-00 01B-050A72-63-00 01C-05072-63-00 01C-050A
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-13-79-610-004  Draining of the Accessory Drive Section
 71-00-00-710-006  Minimum Idle Check
 71-13-00-010-040  Opening of the Fan Cowl Doors
 71-13-00-410-040  Closing of the Fan Cowl Doors
 78-30-00-081-041  Make the Thrust Reverser Serviceable after
 Maintenance
 78-30-00-481-041  Make the Thrust Reverser Unserviceable for
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 1(76)