INSIDE OF COUPLING IS NOT LUBRICATED.
Standard Torque Values for Clamps
Figure 209 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-50-11
 ALL  ú ú 01 Page 214 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E77114
A
737-300/400/500MAINTENANCE MANUAL
 CIRCUIT BREAKER RESET - MAINTENANCE PRACTICES
_____________________________________________
 TASK 20-60-01-862-001
 1.  Circuit Breaker Reset_____________________
 A. General
 (1)  
This procedure is for on-the-ground maintenance.

 (2)  
Circuit breakers open when there is an electrical overload in the airplane system. A circuit breaker that opens because of an electrical overload is known as a "tripped" circuit breaker.

 (3)  
If there are currently specific instructions for the reset of a tripped circuit breaker in maintenance and troubleshooting procedures, follow those instructions.

 (4)  
A defective circuit breaker can cause the circuit breaker to open. Make sure that the circuit breaker is serviceable.

 (5)  
Use your judgement and airline policy to reset a tripped circuit breaker.

 (6)  
Monitor the airplane to see if a tripped circuit breaker occurs again on subsequent flights.

 (7)  
Do not reset a tripped circuit breaker until you know the cause for the tripped circuit breaker and that the circuit breaker can be safely reset. Fires have occurred in which the tripped circuit breakers were reset without an examination of the cause.

 (8)  
Use this procedure to reset a tripped circuit breaker:

 (a)  
If you know that the circuit breaker is serviceable.

 (b)  
If this procedure is in agreement with your airline policy.

 (c)  
If you cannot determine the cause for the tripped circuit breaker.

 (d)  
If you cannot determine whether it is safe to reset the circuit breaker.

 B. References
 (1)  
AMM (applicable procedure)

 (2)  
SWPM (applicable procedure)

 (3)  
WDM (applicable diagram)

 C. Procedure
 S 862-002
 (1)  
Attach a DO-NOT-CLOSE tag to the tripped circuit breaker.

 (2)
Install a circuit breaker lock on the tripped circuit breaker.

 S 862-004

 (3)  
If the tripped circuit breaker is one of three circuit breakers protecting a 3-phase circuit:

 S 862-003
 (a)  Open the other two circuit breakers.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-60-01
 ALL  ú ú 01 Page 201 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  
Attach DO-NOT-CLOSE tags.

 (c)  
Install circuit breaker locks.

 S 862-005
 (4)  Look in the aircraft logbook to find if there is recorded data about a "tripped" circuit breaker, such as:
 (a)  
The condition existing when the circuit breaker trip occurred.

 (b)  
The conditions existing when the circuit breaker was reset.

 (c)  
The results of resetting the circuit breaker.

 S 862-006
 (5)  Do a visual check for damage to electrical wiring and system components related to the tripped circuit breaker. If necessary, refer to the Wiring Diagram Manual (WDM). Look for these types of damage:
 (a)  
Electrical shorting

 (b)  
Electrical arcing

 (c)  
Corrosion on the contacts of the electrical wiring and system components

 (d)  
Abrasion of the electrical wiring and system components

 (e)  
Cracks on the insulation of the electrical wiring

 (f)  
Split wires

 NOTE: A split wire is when you can see the conductor through
____ the crack in the insulation of the electrical wiring.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES(155)