NOTE: If the destination component is active, the
____ installation sequence will begin and the RDY light will come on. When the data transfer begins, the PROG light will come on. The RDY light can flash when the component validates the data. If the software is on more than one disk, the CHNG light will come on when it is time to put in the subsequent disk.
(c) If the CHNG light comes on, wait approximately 10 seconds and then push the eject button.
NOTE: The installation can fail if you wait too long
____ before you remove and install disks.
1) Remove the disk from the disk drive. 2) Put the subsequent disk into the disk drive. 3) If there are more than two disks for the software
installation, then remove and install disks until the COMP light shows.
(d)
When the COMP light comes on, wait approximately 10 seconds and then push the eject button.
(e)
Remove the disk from the disk drive.
(f)
If there was a plastic protective disk in the disk drive before you installed software, then put it back into the disk drive.
S 862-013
(11)
Set the system select switch on the data loader control panel to the NORM position.
(12)
Close the front cover on the ADL.
S 412-014
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-15-11
ALL ú ú 01 Page 211 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 742-015
(13) Make sure that the correct software part numbers are installed in the component.
NOTE: The software installation task for the component has the
____ steps to do a software configuration check.
S 862-016
(14)
Remove electrical power (AMM 24-22-00/201).
E.
Teledyne Airborne Data Loader Procedure
S 862-017
(1) Supply electrical power (AMM 24-22-00/201).
(a) Make sure that the power is not removed while you install software.
NOTE: A power interruption will cause a failure of the
____
software installation.
S 862-018
(2)
Make sure that the system select switch on the data loader control panel (P21, P23 or P37) is set to the NORM position.
S 862-019
(3)
Open this circuit breaker:
(a) On the circuit breaker panel, P18:
1) AIRBORNE DATA LOADER
S 012-020
(4)
To open the ADL front cover, turn the cover knob clockwise and pull.
S 862-021
(5)
Push the eject button on the ADL.
(a) If a plastic protective disk is ejected from the disk drive, then remove it.
S 862-022
(6)
Close this circuit breaker:
(a) On the P18 panel:
1) AIRBORNE DATA LOADER
(7)
Wait until the display shows INSERT DISK #1.
S 862-023
NOTE: The display lights and the ADL FAIL light will go on and
____ off while the ADL does a self test. When the self test is complete, the display will show INSERT DISK #1.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-15-11
ALL ú ú 01 Page 212 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 862-024
(8)
Make sure that the circuit breakers are closed for the applicable component or system that will receive the new software.
S 422-025
(9)
Do these steps at the ADL to install the software:
NOTE: You must know the correct software part numbers for the
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 STANDARD PRACTICES(89)
