C.  Procedure
 S 024-003
 (1)  
Disconnect the electrical connector from the controller.

 (2)  
Remove the screws and the washers.

 (3)  
Remove the controller.

 S 024-004
 S 024-005
 TASK 21-51-52-404-017
 3.  35°F Controller - Installation (Fig. 401)______________________________
 A.  References
 (1)  24-22-00/201, Electrical Power
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-51-52
 ALL  ú ú 02 Page 401 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
35`F CONTROLLER SEE B
ECS BAY SEE A
BSEE 35`F CONTROLLER 
35`F CONTROLLER  CONNECTOR ELECTRICAL  A ECS BAY  FWD 

SCREWWASHER (4 LOCATIONS)
35`F CONTROLLER
B
35 Degree Fahrenheit Controller Installation Figure 401
G92621
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-51-52
 ALL  ú ú 02 Page 402 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.

A
737-300/400/500MAINTENANCE MANUAL
Access
 (1)  Location Zones 212 Left Air Conditioning Equipment Bay 214 Right Air Conditioning Equipment Bay
Procedure
 S 424-006
 (1)  
Put the controller in its position.

 S 424-007

 (2)  
Install the washers and the screws.

 S 424-008

 (3)
Install the electrical connector on the controller.Do a Post Installation Test of the Controller

 S 864-009

 (1)  
Supply electrical power (AMM 24-22-00/201).

 S 864-010

 (2)  
Close these circuit breakers on the P6-4 panel:

 (a)  
6A2, TEMP CONTROL 35 DEG F CONTROL L

 (b)  
6A1, TEMP CONTROL 35 DEG F CONTROL R

 S 864-011
 (3)  
Put the L PACK and R PACK switches to the OFF position.

 S 864-012

 (4)  
Do these steps to do a BITE test on the controller:

 (a)  
Push the GO and the NO GO lights on the controller. 1) Make sure the lights come on when you push them.

 (b)  
Rotate the TEST SWITCH to position 1.
 1) Make sure the GO light comes on.

 (c)  
Rotate the TEST SWITCH to position 2. 1) Make sure the GO light comes on. 2) Make sure the 35 degree F valve goes to the full open

 position.

 (d)  
Rotate the TEST SWITCH to position 3.
 1) Make sure the GO light comes on.

 (e)  
Rotate the TEST SWITCH to position 4. 1) Make sure the GO light comes on. 2) Make sure the 35 degree F valve goes to the full closed

 position.

 (f)  
Rotate the TEST SWITCH to position 5.
 1) Make sure the GO light comes on.

 (g)  
Rotate the TEST SWITCH to the FLIGHT position.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-51-52
 ALL  ú ú 02 Page 403 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 E. Put the Airplane Back to its Usual Condition
 S 414-013
 (1) Do this step if you installed the controller for the left pack:
 (a) Close the left ECS bay access door.
 S 414-014
 (2) Do this step if you installed the controller for the right pack:
 (a) Close the right ECS bay access door.
 S 864-015
 (3)
Put the L PACK and the R PACK switches to the AUTO position.

 S 864-016

 (4)
Remove electrical power if it is not necessary (AMM 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空調 AIR CONDITIONING 2(34)