21-52-91
 (PRE-SB 21-1123)  ú ú 01 Page 403 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500MAINTENANCE MANUAL
ARM
PIN HOLE FOR
RIGGING PIN
(1/4-INCH DIAMETER)

TORQUE SHAFT
RIG PIN HOLE FOR LOUVER ASSEMBLY
D
RIG PIN HOLE FOR FULL (GROUND)
RIG PIN HOLE FOROPEN POSITION
FLIGHT OPEN POSITION (5/16-INCH DIAMETER)
TORQUE SHAFT QUADRANT
E

Ram Air Exhaust Modulation Louver Assembly Installation
Figure 401 (Sheet 2)

H33564
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH RAM AIR EXHAUST LOUVERS ú

 21-52-91
 (PRE-SB 21-1123)  ú ú 02 Page 404 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (f)  
Turn the arm until the louvers move to the full open position.

 (g)  
Install the 1/4-inch rigging pin to hold the louvers in the open position (Fig. 401, Detail D).

 (h)  
Make sure the ram air actuator is in the retracted position (ram air door is in the full open position).

 (i)  
Install the 5/16-inch rigging pin through the torque shaft quadrant (Fig. 401, Detail E).

 (j)  
Remove the tape which you installed to hold the torque shaft sections together.

 (k)  
Connect the universal joint to the arm.

 (l)  
Align the bolt holes of the torque shaft and install the bolts.

 (m)  
Align the pin holes in the universal joint with the pin holes in the arm.

 NOTE: If the arm does not have the pin holes you will have to
____ drill the pin holes. Use a drill bit with a 0.190 (+0.002/-0.005) inch diameter.
 (n)  
Apply the primer to the spring pins.

 (o)  
Install the spring pins to attach the universal joint to the arm.

 (p)  
Connect the spring pins together with a new lockwire.

 (q)  
Remove the rigging pins.

 S 714-007
 (2)  
Do the operational test of the ram air system (Ref 21-52-00/501).

 S 414-008

 (3)  
Close the access doors for the air conditioning bay and the ram air duct.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH RAM AIR EXHAUST LOUVERS ú

 21-52-91
 (PRE-SB 21-1123)  ú ú 01 Page 405 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 RAM AIR EXHAUST MODULATION LOUVER ASSEMBLY - REPAIRS
____________________________________________________
 1.  General_______
 A.  This procedure gives instructions to replace these damaged components of the ram air exhaust modulation louver assembly: the louvers, the louver bearings, and the shafts.
 TASK 21-52-91-308-001
 2.  Ram Air Exhaust Modulation Louver Assembly Repairs (Fig. 801)__________________________________________________
 A.  Consumable Materials
 (1) A00900 - Sealant - Dow Corning RTV
 B.  References
 (1)
21-52-00/501, Ram Air System

 (2)
24-22-00/201, Electrical Power

 C.  Access
 (1)  Location Zones
 212/214 Air Conditioning Equipment Bay
 211/213 Ram Air Duct

 D.  Procedure
 S 868-002
 (1)
Supply electrical power (Ref 24-22-00/201).

 S 218-003

 (2)
Make sure these circuit breakers are closed on the P6 panel:

 (a)
L RAM MOD

 (b)
R RAM MOD

 (c)
RAM MOD CONT

 (3)
Operate the ram air system to open the louvers (Ref 21-52-00/501).

 (4)
Make sure the louvers are in the full open position.

 S 718-004
 S 218-005
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH RAM AIR EXHAUST LOUVERS ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空調 AIR CONDITIONING 2(73)