TASK 22-21-11-745-022
 3. Mach Trim Actuator Test (DFCS BITE)(-912 and on FCC)
_______________________
 A. References
 (1)  
AMM 12-31-01/201, General Zone Diagram

 (2)  
AMM 24-22-00/201, Electrical Power Control

 (3)  
AMM 27-31-00/201, Elevator and Tab Control System

 (4)  
AMM 27-41-00/501, Horizontal Stabilizer Trim Control System

 B. Access
 (1)  
Location Zone
 705 Tail Cone Access Door

 (2)  
Access Panel
 3802 Tail Cone Access Door

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-21-11
 ALL  ú ú 01 Page 503 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 C. Prepare for DFCS BITE
 S 865-024
 (1)  
Make sure the BAT switch is in the ON position (Pilots forward overhead panel).

 S 865-025

 (2)  
Make sure that the STANDBY POWER switch is in the AUTO position (Pilots forward overhead panel).

 S 865-026

 (3)  
Supply electrical power (AMM 24-22-00/201, Electrical Power Control).

 S 865-027

 (4)  
Put the MASTER DIM and TEST switch, on the P2 center instrument panel, to the TEST position.

 S 865-030

 (5)  
Make sure all indicator lamps and annunciator lights on the pilots panel operate correctly.

 S 865-031

 (6)  
Make sure that all of the circuit breakers (P6 and P18 circuit breaker panels) for the systems shown below are closed and that the systems operate.

 (a)  
FMCS

 (b)  
DADC (No. 1 and 2)

 (c)  
Interphone system

 S 865-032
 (7)  
Make sure that the LANDING GEAR LATCH and AIR/GROUND relay circuit breaker (P6 panel) is closed (relay must be in GND position).

 S 865-033

 (8)  
Close the circuit breakers shown below (P6 and P18 circuit breaker panels):

 (a)  
DFCS (A and B)

 (b)  
Mach Trim (A and B)

 (c)  
Yaw Damper

 (9)
Make sure all instrument switches are in the normal position.

 S 755-034

 (10)
 Make sure the ground sensing light is off, to show the airplane is in the ground mode. The light is red, and can be found on the E11 shelf, forward of the nose wheel well.

 (11)
 Make sure the indicated airspeed (IAS) is less than 50 knots.

 S 865-061
 S 865-035
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-21-11
 ALL  ú ú 01 Page 504 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 015-036
 (12) Remove access panel 3802 on the tail cone (AMM 12-31-41/201).
 D. Mach Trim Actuator Test
 NOTE: DFCS BITE is done with the FMCS CDU.
____
 S 745-037
 (1)  Do the steps below to do the DFCS BITE test.
 (a)  
Push the INIT/REF key on the FMCS CDU. Make sure that the CDU shows the POS INIT or PERF INIT page.

 (b)  
Push the line select key (LSK) adjacent to (<INDEX) and make sure the CDU shows INIT REF INDEX 1/1.

 (c)  
Push the LSK adjacent to (MAINT>). Make sure the CDU shows MAINT BITE INDEX 1/1.

 (d)  
Push the LSK adjacent to (<DFCS) and make sure the CDU shows DFCS BITE TEST page 1/2.

 (e)  
Push the NEXT PAGE key and make sure the CDU shows DFCS BITE TEST page 2/2.

 (f)  
Push the LSK adjacent to (<RIGGING) and make sure the CDU shows DFCS BITE TEST RIGGING -A/-B 50.00.

 (g)  
Push the LSK adjacent to (MACH TRIM>) and make sure the CDU shows DFCS BITE TEST MACH TRIM RIG 57.00.

 (h)  
Push the LSK adjacent to (<CHANNEL) for the selection of mach trim rigging for channel A.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(122)