22-21-31
 ALL  ú ú 02 Page 403 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 424-030
 (2)  
Use the wrench set to install the mach trim flap switch.

 S 434-026

 (3)  
Do these steps to install the Mach Trim Flap Switch.

 (a)  
Put the switch in the flap control unit and install the retaining nut and the roller guide. Install the pin to attach the roller guide.

 (b)  
Install two switch wires in the connectors and connect to the receptacle.

 (c)  
Install the other switch wire to the spice lug.

 (d)  
Replace the wire bundle ties.

 (e)  
Install the two support clamps on the wire bundle.

 S 824-016
 (4)  Do the Mach Trim Flap Switch - Adjustment/Test procedure
 (AMM 22-21-31/501).

 E. Put the airplane back to its initial condition
 S 434-019
 (1)
Make sure that there is lockwire thru the switch retaining nuts.

 S 394-020

 (2)  
Apply a light layer of grease to the surface of the gasket.

 S 414-027

 (3)  
Install the switch cover on the flap control unit.

 S 414-021

 (4)  
Install the inboard flap track fairings (AMM 27-51-32/401).

 (5)  
Remove the electrical power if it is not necessary.

 S 864-024
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-21-31
 ALL  ú ú 02 Page 404 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 MACH TRIM FLAP SWITCH - ADJUSTMENT/TEST
_______________________________________
 1.  General
_______
 A.  This procedure contains two tasks. The first is the Mach Trim Flap Switch adjustment and the second is the Mach Trim Flap Switch test.
 B.  The Mach Trim Flap Switch S290 and flap limit switches are installed on the flap control unit in the right wheel well (Fig. 501).
 TASK 22-21-31-825-044
 2.  Mach Trim Flap Switch Adjustment
________________________________
 A.  Standard Tools and Equipment
 (1)  Grease - MIL-G-23827 (Ref 20-30-21)
 B.  References
 (1)  
12-31-01/201, General Zone Digram

 (2)  
20-30-21/201, Lubricants

 (3)  
24-22-00/201, Manual Control

 (4)  
AMM 27-51-32/401, Fairings, Inboard Flap Track

 (5)  
AMM 27-51-87/401, Switches - Flap Limit

 C.  Access
 (1)  Location Zone
 17 Right Main Wheel Well

 D.  Prepare for Adjustment
 S 865-001
 (1)
Supply electrical power (Ref 24-22-00/201, Manual Control).

 S 865-002

 (2)  
Close the circuit breakers shown below on circuit breaker panel P6-2:

 (a)  
ALT T.E. FLAP DRIVE AC

 (b)  
FLAP

 S 015-003
 (3)  Remove number 4 and 5 Inboard Flap Track Fairings
 (AMM 27-51-32/401).

 NOTE: You must remove the fairings for access to measure the ball
____ screw nut location for the switch adjustment.
 S 015-004
 (4) Remove the switch cover from the flap control unit (Fig. 501).
 E.  Mach Trim Flap Switch Adjustment
 S 865-037
 (1)  Set the alternate flap master switch to ARM. Use the alternate flap switch to put the flaps at 1 unit.
 NOTE: Do not disconnect the torque tubes to set the flaps.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(127)