Autopilot Disengage Switch Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-41
ALL ú ú 01 Page 402 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
6) AFCS A MACH TRIM AC
7) AFCS A MACH TRIM DC
S 024-010
(2) Remove the autopilot disengage switch:
(a) At the center of the control wheel, remove the medallion cover, the approach plate assembly (7), and the sponge rubber pad (8).
NOTE: It is not necessary to remove the terminal block
____
insulator.
(b) Use the extraction tool to disconnect the eight wires on top of the terminal block insulator.
NOTE: Do not disconnect the wire that has the red and white
____
stripes.
(c)
Attach one end of the threading wire around the wire bundle (eight wires) that connect to the switch.
(d)
Remove the screw (3) from the switch plate (2).
(e)
Pull the switch (1) and the wire bundle through the control wheel horn (5).
NOTE: Permit approximately 3 inches of the threading wire to
____ come out of the control wheel.
(f)
Remove the threading wire from the wire bundle.
(g)
Remove the switch plate (2) from the switch.
TASK 22-11-41-404-011
3. Autopilot Disengage Switch Installation (Fig. 401)
_______________________________________
A. Special Tools and Equipment
(1) M15570-20 - Insertion and Extraction Tool, Deutsch Corp., Municipal Airport, Banning, California 92220
B. Standard Tools and Equipment
(1) Threading Wire - 30-inch length of standard wire (No. 18 to 22 gage), without insulation if possible.
C. Consumable Materials
(1) C00260 - Wet primer - BMS 10-11, Type 1
D. References
(1)
AMM 22-11-41/501, Autopilot Disengage Switch - Adjustment/Test
(2)
24-22-00/201, Manual Control
(3)
29-15-00/201, Hydraulic System A, B and Standby
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-41
ALL ú ú 01 Page 403 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
E. Access
(1) Location Zones
101 Control Cabin, LH
102 Control Cabin, RH
F. Install the Autopilot Disengage Switch
S 864-012
(1) Make sure these circuit breakers are open and the DO-NOT-CLOSE tags are attached:
(a)
P6-2 Circuit Breaker Panel
1) AFCS B SNSR EXC AC
2) AFCS B FCC DC
3) AFCS ENGAGE INTLK B
4) AFCS B WARN LIGHT BAT
5) AFCS B MACH TRIM AC
6) AFCS B MACH TRIM DC
(b)
P18-1 Circuit Breaker Panel
1) AFDS MCP DC
2) AFCS A SNSR EXC AC
3) AFCS A FCC DC
4) AFCS ENGAGE INTLK A
5) AFCS A WARN LIGHT BAT
6) AFCS A MACH TRIM AC
7) AFCS A MACH TRIM DC
S 424-013
(2) Install the autopilot disengage switch:
(a)
Apply some wet primer on the threads of the switch and the switch plate.
(b)
Install the switch plate (2) on the switch.
(c)
Attach one end of the threading wire, the end that comes out from the wheel horn, around the wire bundle (eight wires).
(d)
Pull the wire bundle down through the control wheel horn with the opposite end of the threading wire.
(e)
Tighten the switch plate (2) to the control wheel horn with the screw (3).
(f)
Remove the threading wire from the wire bundle.
(g)
Use the insertion tool to connect the wire bundle (eight wires) to the wires in the control column (Ref Table 401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 自動飛行 AUTOFLIGHT 2(55)
